Call Recording is blank

[sundar]

Hi,

Some of my voice call recording are blank, i can hear the initial ring and after the call is answered there is no voice in the recorded file. Could this be due to toomuch load on the server, sometimes the server load goes to as high 12 . And most of the files with blank recording are more than 15min in length.

Can you please suggestion me on possible reasons with blank voice file(the files are in WAV format).

Thanks for your time.
Sundar.

[rajeevpn]

Yes a loadavg of 12 will definitely contribute to this problem!
How many agents?
How many servers?
What version?

[sundar]

total agents 10-12
One server p4 with 1GB RAM
asterisk-1.2.17
All calls recorded



If it is due to the load, it should give recording with some voice (with lots of voice breaks)..but the file is totally blank except the initial ring. Could this be due to some wrong meetme being recorded...(just a guess)..?

The following is my extension.conf file

;
; Static extension configuration file, used by
; the pbx_config module. This is where you configure all your
; inbound and outbound calls in Asterisk.
;
; This configuration file is reloaded
; - With the "extensions reload" command in the CLI
; - With the "reload" command (that reloads everything) in the CLI

;
; The "General" category is for certain variables.
;
[general]
;
; If static is set to no, or omitted, then the pbx_config will rewrite
; this file when extensions are modified. Remember that all comments
; made in the file will be lost when that happens.
;
; XXX Not yet implemented XXX
;
static=yes
;
; if static=yes and writeprotect=no, you can save dialplan by
; CLI command 'save dialplan' too
;
writeprotect=no
;
; If autofallthrough is set, then if an extension runs out of
; things to do, it will terminate the call with BUSY, CONGESTION
; or HANGUP depending on Asterisk's best guess (strongly recommended).
;
; If autofallthrough is not set, then if an extension runs out of
; things to do, asterisk will wait for a new extension to be dialed
; (this is the original behavior of Asterisk 1.0 and earlier).
;
autofallthrough=yes
;
; If clearglobalvars is set, global variables will be cleared
; and reparsed on an extensions reload, or Asterisk reload.
;
; If clearglobalvars is not set, then global variables will persist
; through reloads, and even if deleted from the extensions.conf or
; one of its included files, will remain set to the previous value.
;
clearglobalvars=no
;
; If priorityjumping is set to 'yes', then applications that support
; 'jumping' to a different priority based on the result of their operations
; will do so (this is backwards compatible behavior with pre-1.2 releases
; of Asterisk). Individual applications can also be requested to do this
; by passing a 'j' option in their arguments.
;
priorityjumping=no
;
; You can include other config files, use the #include command
; (without the ';'). Note that this is different from the "include" command
; that includes contexts within other contexts. The #include command works
; in all asterisk configuration files.
;#include "filename.conf"

; The "Globals" category contains global variables that can be referenced
; in the dialplan with ${VARIABLE} or ${ENV(VARIABLE)} for Environmental
; variables,
; ${${VARIABLE}} or ${text${VARIABLE}} or any hybrid
;
[globals]
CONSOLE=Console/dsp ; Console interface for demo
;CONSOLE=Zap/1
;CONSOLE=Phone/phone0
IAXINFO=guest ; IAXtel username/password
;IAXINFO=myuser:mypass
;TRUNK=Zap/g2 ; Trunk interface
;CONSOLE=IAX2/VoicePulse1
;TRUNK=IAX2/VoicePulse1
TRUNK=SIP/myvoip
TRUNKIAX=IAX2/VoicePulse1
TRUNKX=SIP/sundar
;
; Note the 'g2' in the TRUNK variable above. It specifies which group (defined
; in zapata.conf) to dial, i.e. group 2, and how to choose a channel to use in
; the specified group. The four possible options are:
;
; g: select the lowest-numbered non-busy Zap channel
; (aka. ascending sequential hunt group).
; G: select the highest-numbered non-busy Zap channel
; (aka. descending sequential hunt group).
; r: use a round-robin search, starting at the next highest channel than last
; time (aka. ascending rotary hunt group).
; R: use a round-robin search, starting at the next lowest channel than last
; time (aka. descending rotary hunt group).
;
TRUNKMSD=1 ; MSD digits to strip (usually 1 or 0)
;TRUNK=IAX2/user:pass@provider

;
; Any category other than "General" and "Globals" represent
; extension contexts, which are collections of extensions.
;
; Extension names may be numbers, letters, or combinations
; thereof. If an extension name is prefixed by a '_'
; character, it is interpreted as a pattern rather than a
; literal. In patterns, some characters have special meanings:
;
; X - any digit from 0-9
; Z - any digit from 1-9
; N - any digit from 2-9
; [1235-9] - any digit in the brackets (in this example, 1,2,3,5,6,7,8,9)
; . - wildcard, matches anything remaining (e.g. _9011. matches
; anything starting with 9011 excluding 9011 itself)
; ! - wildcard, causes the matching process to complete as soon as
; it can unambiguously determine that no other matches are possible
;
; For example the extension _NXXXXXX would match normal 7 digit dialings,
; while _1NXXNXXXXXX would represent an area code plus phone number
; preceded by a one.
;
; Each step of an extension is ordered by priority, which must
; always start with 1 to be considered a valid extension. The priority
; "next" or "n" means the previous priority plus one, regardless of whether
; the previous priority was associated with the current extension or not.
; The priority "same" or "s" means the same as the previously specified
; priority, again regardless of whether the previous entry was for the
; same extension. Priorities may be immediately followed by a plus sign
; and another integer to add that amount (most useful with 's' or 'n').
; Priorities may then also have an alias, or label, in
; parenthesis after their name which can be used in goto situations
;
; Contexts contain several lines, one for each step of each
; extension, which can take one of two forms as listed below,
; with the first form being preferred. One may include another
; context in the current one as well, optionally with a
; date and time. Included contexts are included in the order
; they are listed.
;
;[context]
;exten => someexten,priority[+offset][(alias)],application(arg1,arg2,...)
;exten => someexten,priority[+offset][(alias)],application,arg1|arg2...
;
; Timing list for includes is
;
; <time range>|<days of week>|<days of month>|<months>
;
;include => daytime|9:00-17:00|mon-fri|*|*
;
; ignorepat can be used to instruct drivers to not cancel dialtone upon
; receipt of a particular pattern. The most commonly used example is
; of course '9' like this:
;
;ignorepat => 9
;
; so that dialtone remains even after dialing a 9.
;

[default]

; Extension 8600 + 8601 conference rooms
exten => 8600,1,Meetme,8600
exten => 8601,1,Meetme,8601

exten => _1.,1,Dial(SIP/${EXTEN})

exten => 100,1,Playback,transfer|skip ; "Please hold while..."
exten => 100,2,Dial,sip/100|20|to ; Ring, 20 secs max
exten => 100,3,Voicemail,100 ; Send to voicemail...

exten => 101,1,Playback,transfer|skip ; "Please hold while..."
exten => 101,2,Dial,sip/101|20|to ; Ring, 20 secs max
exten => 101,3,Voicemail,101 ; Send to voicemail...

exten => 100,1,Playback,transfer|skip ; "Please hold while..."
exten => 100,2,Dial,sip/100|20|to ; Ring, 20 secs max
exten => 100,3,Voicemail,100 ; Send to voicemail...

exten => 2000,1,Playback,transfer|skip ; "Please hold while..."
exten => 2000,2,Dial,sip/2000|20|to ; Ring, 20 secs max
exten => 2000,3,Voicemail,2000 ; Send to voicemail...


exten => 2001,1,Playback,transfer|skip ; "Please hold while..."
exten => 2001,2,Dial,sip/2001|20|to ; Ring, 20 secs max
exten => 2001,3,Voicemail,2001 ; Send to voicemail...


exten => 2002,1,Playback,transfer|skip ; "Please hold while..."
exten => 2002,2,Dial,sip/2002|20|to ; Ring, 20 secs max
exten => 2002,3,Voicemail,2002 ; Send to voicemail...


exten => 2003,1,Playback,transfer|skip ; "Please hold while..."
exten => 2003,2,Dial,sip/2003|20|to ; Ring, 20 secs max
exten => 2003,3,Voicemail,2003 ; Send to voicemail...


exten => 2004,1,Playback,transfer|skip ; "Please hold while..."
exten => 2004,2,Dial,sip/2004|20|to ; Ring, 20 secs max
exten => 2004,3,Voicemail,2004 ; Send to voicemail...


exten => 2005,1,Playback,transfer|skip ; "Please hold while..."
exten => 2005,2,Dial,sip/2005|20|to ; Ring, 20 secs max
exten => 2005,3,Voicemail,2005 ; Send to voicemail...


exten => 2006,1,Playback,transfer|skip ; "Please hold while..."
exten => 2006,2,Dial,sip/2006|20|to ; Ring, 20 secs max
exten => 2006,3,Voicemail,2006 ; Send to voicemail...


exten => 2007,1,Playback,transfer|skip ; "Please hold while..."
exten => 2007,2,Dial,sip/2007|20|to ; Ring, 20 secs max
exten => 2007,3,Voicemail,2007 ; Send to voicemail...


exten => 2008,1,Playback,transfer|skip ; "Please hold while..."
exten => 2008,2,Dial,sip/2008|20|to ; Ring, 20 secs max
exten => 2008,3,Voicemail,2008 ; Send to voicemail...


exten => 2009,1,Playback,transfer|skip ; "Please hold while..."
exten => 2009,2,Dial,sip/2009|20|to ; Ring, 20 secs max
exten => 2009,3,Voicemail,2009 ; Send to voicemail...





; Extension 102 - Grandstream hardphone
exten => 102,1,Playback,transfer|skip ; "Please hold while..."
exten => 102,2,Dial,sip/gs102|20|to ; Ring, 20 secs max
exten => 102,3,Voicemail,u102 ; Send to voicemail...
; Extension 2000 Sipura line 1
;exten => 2000,1,Dial,sip/spa2000|30|to ; Ring, 30 secs max
;exten => 2000,2,Voicemail,u2000 ; Send to voicemail...
; Extension 2001 Sipura line 2
;exten => 2001,1,Dial,sip/spa2001|30|to ; Ring, 30 secs max
;exten => 2001,2,Voicemail,u2001 ; Send to voicemail...
; Extension 2020 rings both sipura lines
;exten => 2001,1,Dial,sip/spa2000&sip/spa2001|30|to ; Ring, 30 secs max
;exten => 2001,2,Voicemail,u2000 ; Send to voicemail...
; Extension 301 rings the firefly softphone
exten => 301,1,Dial,(IAX2/firefly01@firefly01/s)
exten => 301,2,Hangup


include => vicidial


; Extension 3429 - Inbound 800 number (1-800-555-3429)
exten => _**3429,1,Ringing
exten => _**3429,2,Answer
exten => _**3429,3,Dial,sip/spa2000&sip/spa2001|30|to ; Ring, 30 secs max
exten => _**3429,4,Voicemail,u2000 ; Send to voicemail...
; Extension 3429 - with ANI [callerID]
exten => _*NXXNXXXXXX*3429,1,Ringing
exten => _*NXXNXXXXXX*3429,2,Answer
exten => _*NXXNXXXXXX*3429,3,Dial,sip/spa2000&sip/spa2001|30|to ; Ring, 30
secs max
exten => _*NXXNXXXXXX*3429,4,Voicemail,u2000 ; Send to voicemail...

; dial a long distance outbound number to the UK
exten => _901144XXXXXXXXXX,1,Dial(${TRUNKX}/${EXTEN:1},55,tTo)
exten => _901144XXXXXXXXXX,2,Hangup

; dial a long distance outbound number to Australia
exten => _901161XXXXXXXXX,1,Dial(${TRUNKX}/${EXTEN:1},,tTo)
exten => _901161XXXXXXXXX,2,Hangup

; dial an 800 outbound number
exten => _91800NXXXXXX,1,Dial(${TRUNK}/${EXTEN:1},,tTo)
exten => _91800NXXXXXX,2,Hangup
exten => _91888NXXXXXX,1,Dial(${TRUNK}/${EXTEN:1},,tTo)
exten => _91888NXXXXXX,2,Hangup
exten => _91877NXXXXXX,1,Dial(${TRUNK}/${EXTEN:1},,tTo)
exten => _91877NXXXXXX,2,Hangup
exten => _91866NXXXXXX,1,Dial(${TRUNK}/${EXTEN:1},,tTo)
exten => _91866NXXXXXX,2,Hangup

; dial a local 727 outbound number with area code
exten => _9727NXXXXXX,1,Dial(${TRUNK}/1${EXTEN:1},,tTo)
exten => _9727NXXXXXX,2,Hangup

; dial a local 813 outbound number with area code
exten => _9813NXXXXXX,1,Dial(${TRUNK}/${EXTEN:1},,tTo)
exten => _9813NXXXXXX,2,Hangup

; dial a long distance outbound number
;exten => _91NXXNXXXXXX,1,Dial(${TRUNKX}/${EXTEN:1},,tTo)
;exten => _91NXXNXXXXXX,2,Hangup

exten => _91.,1,Dial(SIP/912${EXTEN:1}@sundar,,o)
exten => _91.,2,Hangup

; dial a local outbound number (modified because of only LD T1)
exten => _9NXXXXXX,1,Dial(${TRUNK}/1727${EXTEN:1},,tTo)
exten => _9NXXXXXX,2,Hangup

exten => _91NXXNXXXXXX,1,AGI(AGI(agi://127.0.0.1:4577/call_log)
exten => _91NXXNXXXXXX,2,Dial(${TRUNK}/${EXTEN},55,o)
exten => _91NXXNXXXXXX,3,Hangup



; barge monitoring extension
exten => 8159,1,ZapBarge
exten => 8159,2,Hangup

; # timeout invalid rules
exten => #,1,Playback(invalid) ; "Thanks for trying the demo"
exten => #,2,Hangup ; Hang them up.
exten => t,1,Goto(#,1) ; If they take too long, give up
exten => i,1,Playback(invalid) ; "That's not valid, try again"

; Give voicemail at extension 8500
exten => 8500,1,VoicemailMain
exten => 8500,2,Goto(s,6)

; ASTERISK AGENTS LOGINS FOR QUEUES (NOT part of VICIDIAL)
; the following assumes phone agent login and exten are 3 digits and the same
; also assumes that 3-digit login is present in agents.conf and queueus.conf
;Agent Logout then stay onhook, DIAL 54 + 3-digit ID
exten => _54XXX,1,AgentCallbackLogin(||)
; the following are used to login and logout of Asterisk Queues from phone
;Agent Login then stay offhook on the phone, DIAL 55 + 3-digit ID
exten => _55XXX,1,AgentLogin(${EXTEN:1})
;Agent Login then stay onhook, phones will ring, DIAL 56 + 3-digit ID
exten => _56XXX,1,AgentCallbackLogin(||${EXTEN:1}@default)

[vicidial]

; This 'h' exten is VERY important for VICIDIAL usage,
; you will have problems if it is not in your dialplan!

exten => h,1,DeadAGI(agi://127.0.0.1:4577/call_log)
exten => h,2,DeadAGI(agi://127.0.0.1:4577/VD_hangup--HVcause ... EBUG-----${HANGUPCAUSE}-----${DIALSTATUS}-----${DIALEDTIME}-----${ANSWEREDTIME})

; Extension 3429 - Inbound 800 number (1-800-555-3429)
exten => _**3429,1,Ringing
exten => _**3429,2,AGI(agi://127.0.0.1:4577/call_log)
exten => _**3429,3,AGI(call_inbound.agi,spa2000-----8005553429-----Inbound 800-----x-----y-----z-----w)
exten => _**3429,3,Answer
exten => _**3429,4,Dial,sip/100&sip/1001|30|to
exten => _**3429,5,Voicemail,u2000
; Extension 3429 - with ANI [callerID]
exten => _*NXXNXXXXXX*3429,1,Ringing
exten => _*NXXNXXXXXX*3429,2,AGI(agi://127.0.0.1:4577/call_log)
exten => _*NXXNXXXXXX*3429,3,AGI(call_inbound.agi,spa2000-----8005553429-----Inbound 800-----x-----y-----z-----w)
exten => _*NXXNXXXXXX*3429,3,Answer
exten => _*NXXNXXXXXX*3429,4,Dial,sip/100&sip/101|30|to
exten => _*NXXNXXXXXX*3429,5,Voicemail,u2000

; Extension 7275551212 - Inbound local number from PRI with 10 digit delivery
exten => 7275551212,1,Ringing
exten => 7275551212,2,Wait(1)
exten => 7275551212,3,AGI(agi://127.0.0.1:4577/call_log--fullCID--${EXTEN}-----${CALLERID}-----${CALLERIDNUM}-----${CALLERIDNAME})
exten => 7275551212,4,Answer
exten => 7275551212,5,Dial,sip/spa2000&sip/spa2001|30|to
exten => 7275551212,6,Voicemail,u2000

; dial a long distance outbound number to the UK
exten => _901144XXXXXXXXXX,1,AGI(agi://127.0.0.1:4577/call_log)
exten => _901144XXXXXXXXXX,2,Dial(${TRUNKX}/${EXTEN:1},55,tTo)
exten => _901144XXXXXXXXXX,3,Hangup

; dial a long distance outbound number to Australia
exten => _901161XXXXXXXXX,1,AGI(agi://127.0.0.1:4577/call_log)
exten => _901161XXXXXXXXX,2,Dial(${TRUNKX}/${EXTEN:1},,tTo)
exten => _901161XXXXXXXXX,3,Hangup

; dial an 800 outbound number
exten => _91800NXXXXXX,1,AGI(agi://127.0.0.1:4577/call_log)
exten => _91800NXXXXXX,2,Dial(${TRUNK}/${EXTEN:1},,tTo)
exten => _91800NXXXXXX,3,Hangup
exten => _91888NXXXXXX,1,AGI(agi://127.0.0.1:4577/call_log)
exten => _91888NXXXXXX,2,Dial(${TRUNK}/${EXTEN:1},,tTo)
exten => _91888NXXXXXX,3,Hangup
exten => _91877NXXXXXX,1,AGI(agi://127.0.0.1:4577/call_log)
exten => _91877NXXXXXX,2,Dial(${TRUNK}/${EXTEN:1},,tTo)
exten => _91877NXXXXXX,3,Hangup
exten => _91866NXXXXXX,1,AGI(agi://127.0.0.1:4577/call_log)
exten => _91866NXXXXXX,2,Dial(${TRUNK}/${EXTEN:1},,tTo)
exten => _91866NXXXXXX,3,Hangup

; dial a local 727 outbound number with area code
exten => _9727NXXXXXX,1,AGI(agi://127.0.0.1:4577/call_log)
exten => _9727NXXXXXX,2,Dial(${TRUNK}/1${EXTEN:1},,tTo)
exten => _9727NXXXXXX,3,Hangup

; dial a local 813 outbound number with area code
exten => _9813NXXXXXX,1,AGI(agi://127.0.0.1:4577/call_log)
exten => _9813NXXXXXX,2,Dial(${TRUNK}/${EXTEN:1},,tTo)
exten => _9813NXXXXXX,3,Hangup

; dial a long distance outbound number
;exten => _91NXXNXXXXXX,1,AGI(agi://127.0.0.1:4577/call_log)
;exten => _91XXXXXXXXXX,1,AGI(call_log.agi,${EXTEN})
;exten => _91NXXNXXXXXX,2,Dial(${TRUNKX}/${EXTEN:1},,tTo)
;exten => _91NXXNXXXXXX,3,Hangup

exten => _91.,1,AGI(agi://127.0.0.1:4577/call_log)
exten => _91.,1,AGI(call_log.agi,${EXTEN})
exten => _91.,2,Dial(SIP/912${EXTEN:2}@sundar,,o)
exten => _91.,3,Hangup

; dial a local outbound number (modified because of only LD T1)
exten => _9NXXXXXX,1,AGI(agi://127.0.0.1:4577/call_log)
exten => _9NXXXXXX,2,Dial(${TRUNK}/1727${EXTEN:1},,tTo)
exten => _9NXXXXXX,3,Hangup

; parameters for agi-VDADcloser.agi (2 fields separated by five dashes "-----"):
; 1. the full extension formatted by VICIDIAL for internal transfers * separated
; 2. the word START to denote the beginning of the acceptance of the transfer
; inbound VICIDIAL transfer calls [can arrive through PRI T1 crossover or IAX channel]
exten => _90009.,1,Answer ; Answer the line
exten => _90009.,2,AGI(agi-VDADcloser.agi,${EXTEN}-----START)
exten => _90009.,3,Hangup


exten => _990009.,1,Answer
exten => _990009.,2,AGI(agi-VDADcloser.agi,${EXTEN}-----START)
exten => _990009.,3,Hangup


; parameters for agi-VDADcloser_inbound....agi (7 fields separated by five dashes "-----"):
; 1. the full name of the IN GROUP to be used in vicidial for the inbound call
; 2. the phone number that was called, for the log entry
; 3. the callerID or lead_id of the person that called(usually overridden)
; 4. the park extension audio file name if used
; 5. the status of the call initially(usually not used)
; 6. the list_id to insert the new lead under if it is new (and callerID available)
; 7. the phone dialing code to insert with the new lead if new (and callerID available)

; inbound VICIDIAL call with CID delivery through T1 PRI
exten => 1234,1,Ringing ; call ringing
exten => 1234,2,Wait(1) ; Wait 1 second for CID delivery from PRI
exten => 1234,3,Answer ; Answer the line
exten => 1234,4,AGI(agi-VDADcloser_inboundCID.agi,CL_GALLERIA-----7275555134-----Closer-----park----------999-----1)
exten => 1234,5,Hangup

; inbound VICIDIAL call with ANI delivery through robbed-bit T1 (*NXXNXXXXXX*DNIS)
exten => 1234,1,Answer ; Answer the line
exten => 1234,2,AGI(agi-VDADcloser_inboundANI.agi,CL_GALLERIA-----7275555134-----Closer-----park----------999-----1)
exten => 1234,3,Hangup

; inbound VICIDIAL call with prompt for 4-digit fronter code
exten => 1234,1,Answer ; Answer the line
exten => 1234,2,AGI(agi-VDADcloser_inbound.agi,CL_GALLERIA-----7275555134-----Closer-----park----------999-----1)
exten => 1234,3,Hangup


exten => 8612001,1,ZapBarge(1)
exten => 8612002,1,ZapBarge(2)
exten => 8612003,1,ZapBarge(3)
exten => 8612004,1,ZapBarge(4)
exten => 8612005,1,ZapBarge(5)
exten => 8612006,1,ZapBarge(6)
exten => 8612007,1,ZapBarge(7)
exten => 8612008,1,ZapBarge(8)
exten => 8612009,1,ZapBarge(9)
exten => 8612010,1,ZapBarge(10)
exten => 8612011,1,ZapBarge(11)
exten => 8612012,1,ZapBarge(12)
exten => 8612013,1,ZapBarge(13)
exten => 8612014,1,ZapBarge(14)
exten => 8612015,1,ZapBarge(15)
exten => 8612016,1,ZapBarge(16)
exten => 8612017,1,ZapBarge(17)
exten => 8612018,1,ZapBarge(18)
exten => 8612019,1,ZapBarge(19)
exten => 8612020,1,ZapBarge(20)
exten => 8612021,1,ZapBarge(21)
exten => 8612022,1,ZapBarge(22)
exten => 8612023,1,ZapBarge(23)
exten => 8612024,1,ZapBarge(24)

exten => 8600001,1,Meetme,8600001|q
exten => 8600002,1,Meetme,8600002|q
exten => 8600003,1,Meetme,8600003|q
exten => 8600004,1,Meetme,8600004|q
exten => 8600005,1,Meetme,8600005|q
exten => 8600006,1,Meetme,8600006|q
exten => 8600007,1,Meetme,8600007|q
exten => 8600008,1,Meetme,8600008|q
exten => 8600009,1,Meetme,8600009|q
exten => 8600010,1,Meetme,8600010|q
exten => 8600011,1,Meetme,8600011|q
exten => 8600012,1,Meetme,8600012|q
exten => 8600013,1,Meetme,8600013|q
exten => 8600014,1,Meetme,8600014|q
exten => 8600015,1,Meetme,8600015|q
exten => 8600016,1,Meetme,8600016|q
exten => 8600017,1,Meetme,8600017|q
exten => 8600018,1,Meetme,8600018|q
exten => 8600019,1,Meetme,8600019|q
exten => 8600020,1,Meetme,8600020|q
exten => 8600021,1,Meetme,8600021|q
exten => 8600022,1,Meetme,8600022|q
exten => 8600023,1,Meetme,8600023|q
exten => 8600024,1,Meetme,8600024|q
exten => 8600025,1,Meetme,8600025|q
exten => 8600026,1,Meetme,8600026|q
exten => 8600027,1,Meetme,8600027|q
exten => 8600028,1,Meetme,8600028|q
exten => 8600029,1,Meetme,8600029|q

exten => _X48600XXX,1,MeetMeAdmin(${EXTEN:2},T,${EXTEN:0:1})
exten => _X48600XXX,2,Hangup

exten => _X38600XXX,1,MeetMeAdmin(${EXTEN:2},t,${EXTEN:0:1})
exten => _X38600XXX,2,Hangup

exten => _X28600XXX,1,MeetMeAdmin(${EXTEN:2},m,${EXTEN:0:1})
exten => _X28600XXX,2,Hangup

exten => _X18600XXX,1,MeetMeAdmin(${EXTEN:2},M,${EXTEN:0:1})
exten => _X18600XXX,2,Hangup

exten => _55558600XXX,1,MeetMeAdmin(${EXTEN:4},K)
exten => _55558600XXX,2,Hangup
exten => 8300,1,Hangup

exten => 8600051,1,Meetme,8600051
exten => 8600052,1,Meetme,8600052
exten => 8600053,1,Meetme,8600053
exten => 8600054,1,Meetme,8600054
exten => 8600055,1,Meetme,8600055
exten => 8600056,1,Meetme,8600056
exten => 8600057,1,Meetme,8600057
exten => 8600058,1,Meetme,8600058
exten => 8600059,1,Meetme,8600059
exten => 8600060,1,Meetme,8600060
exten => 8600061,1,Meetme,8600061
exten => 8600062,1,Meetme,8600062
exten => 8600063,1,Meetme,8600063
exten => 8600064,1,Meetme,8600064
exten => 8600065,1,Meetme,8600065
exten => 8600066,1,Meetme,8600066
exten => 8600067,1,Meetme,8600067
exten => 8600068,1,Meetme,8600068
exten => 8600069,1,Meetme,8600069
exten => 8600070,1,Meetme,8600070
exten => 8600071,1,Meetme,8600071
exten => 8600072,1,Meetme,8600072
exten => 8600073,1,Meetme,8600073
exten => 8600074,1,Meetme,8600074
exten => 8600075,1,Meetme,8600075
exten => 8600076,1,Meetme,8600076
exten => 8600077,1,Meetme,8600077
exten => 8600078,1,Meetme,8600078
exten => 8600079,1,Meetme,8600079
exten => 8600080,1,Meetme,8600080
exten => 8600081,1,Meetme,8600081
exten => 8600082,1,Meetme,8600082
exten => 8600083,1,Meetme,8600083
exten => 8600084,1,Meetme,8600084
exten => 8600085,1,Meetme,8600085
exten => 8600086,1,Meetme,8600086
exten => 8600087,1,Meetme,8600087
exten => 8600088,1,Meetme,8600088
exten => 8600089,1,Meetme,8600089
exten => 8600090,1,Meetme,8600090
exten => 8600091,1,Meetme,8600091
exten => 8600092,1,Meetme,8600092
exten => 8600093,1,Meetme,8600093
exten => 8600094,1,Meetme,8600094
exten => 8600095,1,Meetme,8600095
exten => 8600096,1,Meetme,8600096
exten => 8600097,1,Meetme,8600097
exten => 8600098,1,Meetme,8600098
exten => 8600099,1,Meetme,8600099
exten => 8600100,1,Meetme,8600100
exten => 8600101,1,Meetme,8600101
exten => 8600102,1,Meetme,8600102
exten => 8600103,1,Meetme,8600103
exten => 8600104,1,Meetme,8600104
exten => 8600105,1,Meetme,8600105
exten => 8600106,1,Meetme,8600106
exten => 8600107,1,Meetme,8600107
exten => 8600108,1,Meetme,8600108
exten => 8600109,1,Meetme,8600109
exten => 8600110,1,Meetme,8600110
exten => 8600111,1,Meetme,8600111
exten => 8600112,1,Meetme,8600112
exten => 8600113,1,Meetme,8600113
exten => 8600114,1,Meetme,8600114
exten => 8600115,1,Meetme,8600115
exten => 8600116,1,Meetme,8600116
exten => 8600117,1,Meetme,8600117
exten => 8600118,1,Meetme,8600118
exten => 8600119,1,Meetme,8600119
exten => 8600120,1,Meetme,8600120
exten => 8600121,1,Meetme,8600121
exten => 8600122,1,Meetme,8600122
exten => 8600123,1,Meetme,8600123
exten => 8600124,1,Meetme,8600124
exten => 8600125,1,Meetme,8600125
exten => 8600126,1,Meetme,8600126
exten => 8600127,1,Meetme,8600127
exten => 8600128,1,Meetme,8600128
exten => 8600129,1,Meetme,8600129
exten => 8600130,1,Meetme,8600130
exten => 8600131,1,Meetme,8600131
exten => 8600132,1,Meetme,8600132
exten => 8600133,1,Meetme,8600133
exten => 8600134,1,Meetme,8600134
exten => 8600135,1,Meetme,8600135
exten => 8600136,1,Meetme,8600136
exten => 8600137,1,Meetme,8600137
exten => 8600138,1,Meetme,8600138
exten => 8600139,1,Meetme,8600139
exten => 8600140,1,Meetme,8600140
exten => 8600141,1,Meetme,8600141
exten => 8600142,1,Meetme,8600142
exten => 8600143,1,Meetme,8600143
exten => 8600144,1,Meetme,8600144
exten => 8600145,1,Meetme,8600145
exten => 8600146,1,Meetme,8600146
exten => 8600147,1,Meetme,8600147
exten => 8600148,1,Meetme,8600148
exten => 8600149,1,Meetme,8600149
exten => 8600150,1,Meetme,8600150
exten => 8600151,1,Meetme,8600151
exten => 8600152,1,Meetme,8600152
exten => 8600153,1,Meetme,8600153
exten => 8600154,1,Meetme,8600154
exten => 8600155,1,Meetme,8600155
exten => 8600156,1,Meetme,8600156
exten => 8600157,1,Meetme,8600157
exten => 8600158,1,Meetme,8600158
exten => 8600159,1,Meetme,8600159
exten => 8600160,1,Meetme,8600160
exten => 8600161,1,Meetme,8600161
exten => 8600162,1,Meetme,8600162
exten => 8600163,1,Meetme,8600163
exten => 8600164,1,Meetme,8600164
exten => 8600165,1,Meetme,8600165
exten => 8600166,1,Meetme,8600166
exten => 8600167,1,Meetme,8600167
exten => 8600168,1,Meetme,8600168
exten => 8600169,1,Meetme,8600169
exten => 8600170,1,Meetme,8600170
exten => 8600171,1,Meetme,8600171
exten => 8600172,1,Meetme,8600172
exten => 8600173,1,Meetme,8600173
exten => 8600174,1,Meetme,8600174
exten => 8600175,1,Meetme,8600175
exten => 8600176,1,Meetme,8600176
exten => 8600177,1,Meetme,8600177
exten => 8600178,1,Meetme,8600178
exten => 8600179,1,Meetme,8600179
exten => 8600180,1,Meetme,8600180
exten => 8600181,1,Meetme,8600181
exten => 8600182,1,Meetme,8600182
exten => 8600183,1,Meetme,8600183
exten => 8600184,1,Meetme,8600184
exten => 8600185,1,Meetme,8600185
exten => 8600186,1,Meetme,8600186
exten => 8600187,1,Meetme,8600187
exten => 8600188,1,Meetme,8600188
exten => 8600189,1,Meetme,8600189
exten => 8600190,1,Meetme,8600190
exten => 8600191,1,Meetme,8600191
exten => 8600192,1,Meetme,8600192
exten => 8600193,1,Meetme,8600193
exten => 8600194,1,Meetme,8600194
exten => 8600195,1,Meetme,8600195
exten => 8600196,1,Meetme,8600196
exten => 8600197,1,Meetme,8600197
exten => 8600198,1,Meetme,8600198
exten => 8600199,1,Meetme,8600199
exten => 8600200,1,Meetme,8600200
; quiet entry and leaving conferences for VICIDIAL
exten => _78600XXX,1,Meetme,${EXTEN:1}|q
; quiet monitor extensions for meetme rooms (for room managers)
exten => _68600XXX,1,Meetme,${EXTEN:1}|mq


; park channel for client GUI parking, hangup after 30 minutes
; create a GSM formatted audio file named "park.gsm" that is 30 minutes long
; and put it in /var/lib/asterisk/sounds
exten => 8301,1,Answer
exten => 8301,2,AGI(park_CID.agi)
exten => 8301,3,Playback(park)
exten => 8301,4,Hangup
exten => 8303,1,Answer
exten => 8303,2,AGI(park_CID.agi)
exten => 8303,3,Playback(conf)
exten => 8303,4,Hangup

; park channel for client GUI conferencing, hangup after 30 minutes
; create a GSM formatted audio file named "conf.gsm" that is 30 minutes long
; and put it in /var/lib/asterisk/sounds
exten => 8302,1,Answer
exten => 8302,2,Playback(conf)
exten => 8302,3,Hangup

; default audio for safe harbor 2-second-after-hello message then hangup
; create a GSM formatted audio file complies with safe harbor rules
; and put it in /var/lib/asterisk/sounds then change filename below
exten => 8307,1,Answer
exten => 8307,2,Playback(vm-goodbye)
exten => 8307,3,Hangup

; this is used for recording conference calls, the client app sends the filename
; value as a callerID recordings go to /var/spool/asterisk/monitor (WAV)
exten => 8309,1,Answer
exten => 8309,2,Monitor(wav,${CALLERIDNAME})
exten => 8309,3,Wait,3600
exten => 8309,4,Hangup

; this is used for recording conference calls, the client app sends the filename
; value as a callerID recordings go to /var/spool/asterisk/monitor (GSM)
exten => 8310,1,Answer
exten => 8310,2,Monitor(gsm,${CALLERIDNAME})
exten => 8310,3,Wait,3600
exten => 8310,4,Hangup

; this is used for playing a message to an answering machine forwarded from AMD in VICIDIAL
; replace conf with the message file you want to leave
exten => 8320,1,WaitForSilence(2000,2) ; AMD got machine. leave message after recording
exten => 8320,2,Playback(conf)
exten => 8320,3,AGI(VD_amd_post.agi,${EXTEN})
exten => 8320,4,Hangup

; this is used to allow the GUI to send you directly into voicemail
; don't forget to set GUI variable $voicemail_exten to this extension
exten => 8501,1,VoicemailMain(s${CALLERIDNUM})
exten => 8501,2,Hangup

; this is used to allow the GUI to send live calls directly into voicemail
; don't forget to set GUI variable $voicemail_dump_exten to this extension
exten => _85026666666666.,1,Wait(2)
exten => _85026666666666.,2,Voicemail(${EXTEN:14})
exten => _85026666666666.,3,Hangup

; this is used for sending DTMF signals within conference calls, the client app
; sends the digits to be played in the callerID field
; sound files must be placed in /var/lib/asterisk/sounds
exten => 8500998,1,Answer
exten => 8500998,2,Playback(silence)
exten => 8500998,3,AGI(agi-dtmf.agi)
exten => 8500998,4,Hangup

; prompt recording AGI script, ID is 4321
exten => 8168,1,Answer
exten => 8168,2,AGI(agi-record_prompts.agi)
exten => 8168,3,Hangup

; playback of recorded prompts
exten => _851XXXXX,1,Answer
exten => _851XXXXX,2,Playback(${EXTEN})
exten => _851XXXXX,3,Hangup

; VICIDIAL_auto_dialer transfer script for no-agent campaigns:
exten => 8364,1,Playback(sip-silence)
exten => 8364,2,AGI(agi://127.0.0.1:4577/call_log)
exten => 8364,3,AGI(agi-VDADtransferBROADCAST.agi,${EXTEN})
exten => 8364,4,AGI(agi-VDADtransferBROADCAST.agi,${EXTEN})
exten => 8364,5,Hangup

; VICIDIAL_auto_dialer transfer script:
exten => 8365,1,Playback(sip-silence)
exten => 8365,1,AGI(agi://127.0.0.1:4577/call_log)
exten => 8365,2,AGI(agi-VDADtransfer.agi,${EXTEN})
exten => 8365,3,AGI(agi-VDADtransfer.agi,${EXTEN})
exten => 8365,4,AGI(agi-VDADtransfer.agi,${EXTEN})
exten => 8365,5,Hangup

; VICIDIAL_auto_dialer transfer script SURVEY at beginning:
exten => 8366,1,Playback(sip-silence)
exten => 8366,1,AGI(agi://127.0.0.1:4577/call_log)
exten => 8366,2,AGI(agi-VDADtransferSURVEY.agi,${EXTEN})
exten => 8366,3,AGI(agi-VDADtransferSURVEY.agi,${EXTEN})
exten => 8366,4,AGI(agi-VDADtransferSURVEY.agi,${EXTEN})
exten => 8366,5,Hangup

; VICIDIAL_auto_dialer transfer script Load Balance Overflow:
exten => 8367,1,Playback(sip-silence)
exten => 8367,1,AGI(agi://127.0.0.1:4577/call_log)
exten => 8367,2,AGI(agi-VDAD_LO_transfer.agi,${EXTEN})
exten => 8367,3,AGI(agi-VDAD_LO_transfer.agi,${EXTEN})
exten => 8367,4,AGI(agi-VDAD_LO_transfer.agi,${EXTEN})
exten => 8367,5,Hangup

; VICIDIAL_auto_dialer transfer script Load Balanced:
exten => 8368,1,Playback(sip-silence)
exten => 8368,1,AGI(agi://127.0.0.1:4577/call_log)
exten => 8368,2,AGI(agi-VDAD_LB_transfer.agi,${EXTEN})
exten => 8368,3,AGI(agi-VDAD_LB_transfer.agi,${EXTEN})
exten => 8368,4,AGI(agi-VDAD_LB_transfer.agi,${EXTEN})
exten => 8368,5,Hangup

; VICIDIAL_auto_dialer transfer script AMD with Load Balanced:
exten => 8369,1,Playback(sip-silence)
exten => 8369,1,AGI(agi://127.0.0.1:4577/call_log)
exten => 8369,2,AMD(3500|1500|300|5000|120|50|5|256)
exten => 8369,3,AGI(VD_amd.agi,${EXTEN})
exten => 8369,4,AGI(agi-VDAD_LB_transfer.agi,${EXTEN})
exten => 8369,5,AGI(agi-VDAD_LB_transfer.agi,${EXTEN})
exten => 8369,6,AGI(agi-VDAD_LB_transfer.agi,${EXTEN})
exten => 8369,7,Hangup

; VICIDIAL auAuto-dial reminder script
exten => 8372,1,Playback(sip-silence)
exten => 8372,1,AGI(agi://127.0.0.1:4577/call_log)
exten => 8372,2,AGI(agi-VDADautoREMINDER.agi,${EXTEN})
exten => 8372,3,AGI(agi-VDADautoREMINDER.agi,${EXTEN})
exten => 8372,4,AGI(agi-VDADautoREMINDER.agi,${EXTEN})
exten => 8372,5,Hangup

[rajeevpn]

Well : when the loadavg goes up, we've noticed a lot of unpredictable things happening - how does the call sound to the agent and someone who is barging in live?

once we had a situation where when the load went up the agent wouldn't hear anything at all!