All installation and configuration problems and questions
Moderators: gerski, enjay, williamconley, Op3r, Staydog, gardo, mflorell, MJCoate, mcargile, Kumba, Michael_N
by frank » Wed Dec 13, 2006 6:53 pm
dear mflorell,
how r you doing today, my name is frank and i m new in this forum and vicidial either. Actually the problem is wht i m facing is that when i use only softphone (eyebeam) the voice is very clear but when i use vicidial the voice is like distorted, very pathetic , could you plz find out where is the problem actually. i shall be very greatfull to you.
i m 100 % sure that there is some problem in vicidial.
Dual Xeon 2.0 with 2 GB with 6 agents only. (Vicidial VERSION: 1.1.12-3)
thanks,
Frank
-
frank
-
- Posts: 11
- Joined: Wed Dec 13, 2006 6:42 pm
by mflorell » Wed Dec 13, 2006 10:41 pm
Most likely it is a problem with meetme, and more specifically a problem with your zaptel timer.
What are you using for a zaptel timer, and what codecs are you using?
Any reason you are not using 2.0.1?
-
mflorell
- Site Admin
-
- Posts: 18384
- Joined: Wed Jun 07, 2006 2:45 pm
- Location: Florida
-
by frank » Fri Dec 15, 2006 5:15 pm
Thanx for replying me, well florell i m using ztdummy for timmer and using g.729 codec , can u plz guide me how can i set my timer to improve voice quality as i m sure there is no problem in codec cause when i make call from softphone with asterisk the voice quality is good but when i make call through vicidial agent login (manual) then voice quality decrease some time good but most of the time very bad distorted.
plz help me out.
-
frank
-
- Posts: 11
- Joined: Wed Dec 13, 2006 6:42 pm
by mflorell » Fri Dec 15, 2006 5:25 pm
Is your kernel timer set to 1000Hz?
If it is and you still have this problem you should try using an X100P card as your timer.
-
mflorell
- Site Admin
-
- Posts: 18384
- Joined: Wed Jun 07, 2006 2:45 pm
- Location: Florida
-
by frank » Sat Dec 16, 2006 3:21 pm
Dear Florell
from where should i check the timer of my kernel, can u plz guide me i am new in all of this.
thanx
-
frank
-
- Posts: 11
- Joined: Wed Dec 13, 2006 6:42 pm
by ramindia » Sun Dec 17, 2006 3:03 am
Hi
with the following command you can check
grep CONFIG_HZ /boot/config-$(uname -r)
but its works only some distro,
kernel timer set to 1000Hz only available 2.6.11 and more
as per i know
you have to rebuild with 1000hz will be good idea
or X100p is the best as per the group ( i have not tried yet)
Ram
-
ramindia
-
- Posts: 688
- Joined: Wed Oct 11, 2006 4:06 am
- Location: India
by Op3r » Sun Dec 17, 2006 4:48 pm
get the x100p. it will only cost you 10-30 usd and can save you a lot of headaches
as i said before, simple solutions makes an admin life better.
Get paid for US outbound Toll Free calls. PM me.
-
Op3r
-
- Posts: 1432
- Joined: Wed Jun 07, 2006 7:53 pm
- Location: Manila
-
Return to Support
Who is online
Users browsing this forum: Google [Bot] and 154 guests