Performance Testing Help

All installation and configuration problems and questions

Moderators: gerski, enjay, williamconley, Op3r, Staydog, gardo, mflorell, MJCoate, mcargile, Kumba, Michael_N

Performance Testing Help

Postby arunvoip » Wed Apr 04, 2007 4:42 am

Hi,

I've two asterisk and vici server. I want to perform Performance Testing and I've read the Performance_testing.txt in doc directory but still is not cleared to me how to perform this like who is going to dial these exten. If some one has done this please guide me in brief details.

thanks

arun
arunvoip
 
Posts: 36
Joined: Fri Jun 16, 2006 1:46 am

Postby bulcrack » Wed Apr 04, 2007 4:51 am

I've done this before, Please post your question so we can answer that.
bulcrack
 
Posts: 24
Joined: Sat Jun 10, 2006 11:01 am
Location: Philippines

Postby arunvoip » Wed Apr 04, 2007 4:59 am

thanks for your reply.

like as per the txt file I've added the code in my exten.conf. now what I've to do after this ?
arunvoip
 
Posts: 36
Joined: Fri Jun 16, 2006 1:46 am

same problem

Postby hemanshurpatel » Wed Nov 28, 2007 12:46 am

hello i am also having the same problem
i have done all the modification as per performancetest.txt file , but it doest tell you how to start
i have upload all the performance test leads , they are 6000 in no, but how to start performance testing ???

no information about this is given, so please can anybody help me?
hemanshurpatel
 
Posts: 42
Joined: Fri Oct 19, 2007 2:13 am

Postby mflorell » Wed Nov 28, 2007 1:16 am

Do you have two servers connected to each other over IAX or SIP?

Have you set up the 999999999999 Remote Agent?
mflorell
Site Admin
 
Posts: 18387
Joined: Wed Jun 07, 2006 2:45 pm
Location: Florida

Postby hemanshurpatel » Wed Nov 28, 2007 1:25 am

yes
i ahve done all 999999999999 setup according to performance-test.txt file

but now dont know how to start this testing and from when i can check this server performance data??
hemanshurpatel
 
Posts: 42
Joined: Fri Oct 19, 2007 2:13 am

Postby hemanshurpatel » Wed Nov 28, 2007 6:37 am

hasnt anyone done this performance testing?

Actualiy i need some figures about how many agents at a time can be supported and their bandwidth usage, CUP usage,etc.

But couldnt make this prformace test? dont know how to satrt it.
please help me.
hemanshurpatel
 
Posts: 42
Joined: Fri Oct 19, 2007 2:13 am

Postby hemanshurpatel » Fri Nov 30, 2007 4:14 am

still waiting

i wonder , hasnt anybudy done this sort of testing?
then how will you find the performance data of vicidial server?
hemanshurpatel
 
Posts: 42
Joined: Fri Oct 19, 2007 2:13 am

Postby marmu » Tue Jun 07, 2011 7:31 am

Hi all,

I could also use some help regarding performance testing. I altered aéverything mentioned in the /usr/src/astguiclient/agc_2.2.0/docs/PERFORMANCE_TESTING.txt

I added a remote agent, as described.

The extensions for the control server were already in place. I added the TESTTRUNK to the extensions.conf of the test server. The extensions "_91999NXXXXXX" and "999999999999" were already configured.

I also edited the sip.conf files of both systems according to the PERFORMANCE_TESTING.txt. I only change the IP-address to the IP-address of my control server. Anything wrong with that?

Test-Server:
Code: Select all
vicibox-b1*CLI> sip show peers
Name/username              Host            Dyn Nat ACL Port     Status         
VICItest/VICItest          (Unspecified)    D   N      0        UNKNOWN       


Control-Server:
Code: Select all
asterisk*CLI> sip show peers
Name/username              Host            Dyn Nat ACL Port     Status         
VICItest/VICItest          (Unspecified)    D   N      0        UNKNOWN         


I guess the test server is the one to be "performance tested", right?
But I can't see any output on both systems that would indicate something is going on. So no performance test for me yet :(
Any help is appreciated. Did I miss something, how is the test started?

And want is meant by
Do you have two servers connected to each other over IAX or SIP?

Isn't that done by the entries in the sip.conf on both servers?

UPDATE: still the peer "VICItest" is unreachable on both servers, but the performance test seems to have run. There were up to 1600 channels in use, which created a maximum load of 383 ;) I was also able to blind monitor some sessions and heard music playing. So I guess the performance test kind of ran.
I am curious how the system will perform in the first test sessions within the next months.

Thanks in advance,
Marcus
Vicibox redux 3.1.10 64 bit (ViciBox_Redux.x86_64-3.1.10.iso)
Admin-GUI: VERSION: 2.4-310a - BUILD: 110506-1537 - with some adaptions :)
Asterisk 1.4.39.2-vici | Single Server | wanpipe_voicetime
2x Intel(R) Xeon(R) X5650 | 12 GB | SAS 15k RAID1
marmu
 
Posts: 190
Joined: Fri Mar 12, 2010 6:57 am

Re: Performance Testing Help

Postby maciesse » Fri Apr 20, 2012 12:44 pm

Hi all,

I'm trying to do the performance test too but with no success.

The specs are:
- Cluster environment with 3 identical telephony server and 1 DB/Web/Archive server
- ViciBox Redux 3.1.15 with SVN update
- No other software
- Digium 205P Cards on each telephony.

I did a successful "standard" usage test on one telephony with both manually and list loaded leads.

Now I want to do the performance test, as described in the file in doc folder, using the two others telephony servers.

I'm using an ISDN cross cable to connect them, did the suggested configuration, except for the IP in sip.conf files which I changed with the control server ip.

The test server is successfully trying to call the 999... numbers, there are no errors in the asterisk log but the call are not answered so the test is not really going.

What can be missed???

Thanks in advance!
maciesse
 
Posts: 1
Joined: Fri Apr 20, 2012 12:27 pm


Return to Support

Who is online

Users browsing this forum: No registered users and 147 guests