I have worked a little bit on elastix systems, my hardware is the following : (It is just a test system)
Intel G41, Intel Core2Duo Processor, 2 GB ram, 250 GB Sata Harddrive, One Sangoma A101 PCI Express card, NO other external Hardware.
I was able to successfully install elastix on above system, and configure the PRI card through wancfg_dahdi, and after adding the trunk was able to use it for incoming and outgoing.
But when i try to install vicibox i get certain errors, i have tried it many times but the same thing happens. following is what i did.
installed ViciBox.i686-4.0.1.preload (i just downloaded it on 14th October 2012).
Installed it according the ViciBox_v4-Install.pdf document.
completed phase one, configured Lan, Rebooted.
Then updated OS by using zypper up
Then compiled the wanpipe using wanpipe-compile
I got this output
- Code: Select all
linux-wmvr:~ # wanrouter hwprobe
-------------------------------
| Wanpipe Hardware Probe Info |
-------------------------------
1 . AFT-A101-SH : SLOT=4 : BUS=3 : IRQ=16 : CPU=A : PORT=1 : HWEC=0 : V=37
Sangoma Card Count: A101-2=1
then i installed vicibox-express, and it installed without any errors, and i rebooted the system with reboot command.
when it rebooted i try configuring the sangoma card using wancfg_dahdi, it shows an error, following is the output:
- Code: Select all
linux-wmvr:~ # wancfg_dahdi
########################################################################
# Sangoma Wanpipe #
# Dahdi/Zaptel/SMG/TDMAPI/BOOT Configuration Script #
# v2.39 #
# Sangoma Technologies Inc. #
# Copyright(c) 2009. #
########################################################################
Would you like to generate /etc/asterisk/chan_dahdi.conf
1. YES
2. NO
[1-2]:1
---------------------------------------------
Configuring T1/E1 cards [A101/A102/A104/A108/A116]
---------------------------------------------
A101 detected on slot:4 bus:3
-----------------------------------------------------------
Configuring port 1 on A101 slot:4 bus:3.
-----------------------------------------------------------
Select media type for AFT-A101 on port 1 [slot:4 bus:3 span:1]
1. T1
2. E1
3. Unused
4. Exit
[1-4]:2
Configuring port 1 on 101 as E1, line coding:HDB3, framing:CRC4
1. YES - Keep these settings
2. NO - Configure line coding and framing
[1-2, ENTER='YES']:1
Select clock for AFT-A101 on port 1 [slot:4 bus:3 span:1]
1. NORMAL
2. MASTER
[1-2]:1
Select signalling type for AFT-A101 on port 1 [slot:4 bus:3 span:1]
1. Zaptel/Dahdi - PRI CPE
2. Zaptel/Dahdi - PRI NET
3. Zaptel/Dahdi - E & M
4. Zaptel/Dahdi - E & M Wink
5. Zaptel/Dahdi - FXS - Loop Start
6. Zaptel/Dahdi - FXS - Ground Start
7. Zaptel/Dahdi - FXS - Kewl Start
8. Zaptel/Dahdi - FX0 - Loop Start
9. Zaptel/Dahdi - FX0 - Ground Start
10. Zaptel/Dahdi - FX0 - Kewl Start
11. Sangoma SMG/sangoma_prid- PRI CPE
12. Sangoma SMG/sangoma_prid- PRI NET
[1-12]:1
Select switchtype for AFT-A101 on port 1
1. National ISDN 2
2. Nortel DMS100
3. AT&T 4ESS
4. Lucent 5ESS
5. EuroISDN
6. Old National ISDN 1
7. Q.SIG
[1-7]:1
Configuring port 1 on AFT-A101 as a full E1
1. YES - Use all channels
2. NO - Configure for fractional
[1-2, ENTER='YES']:1
Select dialplan context for AFT-A101 on port 1
1. from-pstn
2. from-internal
3. Custom
[1-3]:1
Port 1 on AFT-A101 configuration complete...
Press any key to continue:
T1/E1 card configuration complete.
Press any key to continue:
------------------------------------
Configuring ISDN BRI cards [A500/B700]
------------------------------------
No Sangoma ISDN BRI cards detected
Press any key to continue:
------------------------------------
Configuring GSM cards [W400]
------------------------------------
No Sangoma GSM cards detected
Press any key to continue:
------------------------------------
Configuring analog cards [A200/A400/B600/B610/B700/B800]
------------------------------------
------------------------------------
Configuring USB devices [U100]
------------------------------------
###################################################################
# SUMMARY #
###################################################################
1 T1/E1 port(s) detected, 1 configured
0 ISDN BRI port(s) detected, 0 configured
0 analog card(s) detected, 0 configured
0 GSM card(s) detected, 0 configured
0 usb device(s) detected, 0 configured
Configurator will create the following files:
1. Wanpipe config files in /etc/wanpipe
2. Dahdi config file /etc/dahdi/system.conf
3. chan_dahdi config file /etc/asterisk/chan_dahdi.conf
Your original configuration files will be saved to:
1. /etc/dahdi/system.conf.bak
2. /etc/asterisk/chan_dahdi.conf.bak
Your configuration has been saved in /etc/wanpipe/debug-2012-10-18.tgz.
When requesting support, email this file to
###################################################################
Configuration Complete! Please select following:
1. YES - Continue
2. NO - Exit
[1-2]:1
Dahdi and Wanpipe configuration complete: choose action
1. Save cfg: Restart Asterisk & Wanpipe now
2. Save cfg: Restart Asterisk & Wanpipe when convenient
3. Save cfg: Stop Asterisk & Wanpipe now
4. Save cfg: Stop Asterisk & Wanpipe when convenient
5. Save cfg: Save cfg only (Not Recommended!!!)
6. Do not save cfg: Exit
[1-6]:1
Stopping Asterisk...
Stopping Wanpipe...
Shutting down wanpipe1 interface: w1g1
w1g1: unknown interface: No such device
Shutting down device: wanpipe1
No devices running, Unloading Modules
Unloading Dahdi modules...
Removing old configuration files...
Copying new Wanpipe configuration files...
Copying new Dahdi configuration file (/etc/dahdi/system.conf)...
Copying new chan_dahdi configuration files (/etc/asterisk/chan_dahdi.conf)...
Starting Wanpipe...
Starting WAN Router...
Loading WAN drivers: wanpipe done.
Starting up device: wanpipe1
wanconfig: Interface w1g1 setup failed
: ioctl(ROUTER_IFNEW,w1g1) failed:
: 22 - Invalid argument
Wanpipe drivers could not setup network interface
Please check /var/log/wanrouter and
/var/log/messages for errors
Configuring interfaces: w1g1 w1g1: unknown interface: No such device
done.
Error executing command:
wanrouter start
Would you like to continue?
1. No - exit
2. YES
[1-2, ENTER='No']:1
PLease guide me where am i going wrong in this setup.
Please tell me if there is any more information needed.
I have not changed anything else in the system, above are the only steps done on the system, i have tried it on a different system, same config, but dual core instead of core2duo, still the same thing happens.
I am pretty sure there is something i am missing, any help would be appreciated.
