vicidial.org

TRUNK=DAHDI/r0

exten => _9XXXXXXXXXXX.,1,AGI(agi://127.0.0.1:4577/call_log)
exten => _9XXXXXXXXXXX.,2,Dial(${TRUNK}/${EXTEN:1},,To)
exten => _9XXXXXXXXXXX.,3,Hangup

we are using 4 port digium card&4 Pri line connected.i have done pri grouping.

In carrier status Congestion(--21-----CONGESTION--) is more.is that problem with dial plan or provider end.

Here is my log

[Feb 13 08:40:40] -- Executing [9098XXXXXXXX@default:1] AGI("Local/9098XXXXXXXX@default-2104,2", "agi://127.0.0.1:4577/call_log") in new stack
[Feb 13 08:40:40] -- AGI Script Executing Application: (EXEC) Options: (Set(_CAMPCUST=TEST))
[Feb 13 08:40:40] -- AGI Script agi://127.0.0.1:4577/call_log completed, returning 0
[Feb 13 08:40:40] -- Executing [9098XXXXXXXX@default:2] Dial("Local/9098XXXXXXXX@default-2104,2", "dahdi/r0/9098XXXXXXXX||To") in new stack
[Feb 13 08:40:40] -- Requested transfer capability: 0x00 - SPEECH
[Feb 13 08:40:40] -- Called r0/9098XXXXXXXX
[Feb 13 08:40:40] -- DAHDI/37-1 is proceeding passing it to Local/9098XXXXXXXX@default-2104,2
[Feb 13 08:40:40] -- DAHDI/37-1 is making progress passing it to Local/9098XXXXXXXX@default-2104,2
[Feb 13 08:40:41] -- Span 2: Channel 0/6 got hangup request, cause 21
[Feb 13 08:40:41] -- DAHDI/37-1 is circuit-busy
[Feb 13 08:40:41] -- Hungup 'DAHDI/37-1'
[Feb 13 08:40:41] == Everyone is busy/congested at this time (1:0/1/0)
[Feb 13 08:40:41] -- Executing [9098XXXXXXXX@default:3] Hangup("Local/9098XXXXXXXX@default-2104,2", "") in new stack
[Feb 13 08:40:41] == Spawn extension (default, 9098XXXXXXXX, 3) exited non-zero on 'Local/9098XXXXXXXX@default-2104,2'
[Feb 13 08:40:41] -- Executing [h@default:1] DeadAGI("Local/9098XXXXXXXX@default-2104,2", "agi://127.0.0.1:4577/call_log--HVcauses--PRI-----NODEBUG-----21-----CONGESTION----------") in new stack
[Feb 13 08:40:42] -- AGI Script agi://127.0.0.1:4577/call_log--HVcauses ... ---------- completed, returning 0

Total 50 agents logged in
Dial Ratio : 3
Congestion : 40%
VERSION: 2.8-410a
BUILD: 130824-2319
Asterisk 1.4.44-vici
Max Calls per Second = 20
Max Trunks=120
Rev: 1983

Post your dialplan entry in use. It does not seem likely that you are trying to dial a 12 digit number that starts with "90". Much more likely that you are dialing an 11 digit number starting with "0". Which means the "9" should have been stripped off by your carrier dialplan entry.

This is handled via "EXTEN:1" in the dial command configuration instead of "EXTEN" (the :1 strips off the first digit). Usually that "9" is used to choose the carrier, and then discarded as having served its purpose. The dial prefix in the campaign is then set to "9" to make this carrier choice. Of course, you could probably change the Campaign Dial Prefix to "X" instead of "9" and that would never put the 9 in front of the number in the first place, so no need to remove it later.

Happy Hunting!

Thank you for your reply.

Problem with service provide end.

It would be very useful (well, probably) to the next person with your problem if you detailed what the problem was and how the carrier fixed it. Also if you "found out" by some method in Vicidial or a Log or whether you just called the carrier.