3-Way Transfer to use Different Carrier

[Nefariousparity]

||Version: 2.4b0.5 || DB Schema Version: 1273 || GoautoDial ISO install || 1.4.39.1-vici||
--------------------------------------------------------------------------------------------------------------------

Hi, so I have two carriers,

One I would like to use primarily for predictive outbound dialing, the other one as failover. However it has 500 channels, so there will be plenty of extra room to use it also primarily for manual dial out, and agent transfers. I have the dial prefex right I believe for manual dial out, just wondering about transfers. Thanks in advance. Here is my config.

Account Entry.

[Connecium-Primary]
type=peer
host=*
port=5060
dtmfmode=rfc2833
disallow=all
allow=ulaw
qualify=yes
canreinvite=no
context=trunkoutbound

[Xcast_OutBound-Failover]
type=friend
host=*
port=5060
dtmfmode=rfc2833
disallow=all
allow=ulaw
qualify=yes
canreinvite=no
context=trunkoutbound

[Xcast_Inbound]
type=friend
host=*
port=5060
dtmfmode=rfc2833
disallow=all
allow=ulaw
qualify=yes
canreinvite=no
context=trunkinbound

Dialplan settings.
exten => _91XXXXXXXXXX,1,AGI(agi://127.0.0.1:4577/call_log)
exten => _91XXXXXXXXXX,2,Dial(SIP/${EXTEN:1}@Connecium,,tTo)
exten => _91XXXXXXXXXX,3,Dial(SIP/${EXTEN:1}@Xcast_OutBound,,tTo)
exten => _91XXXXXXXXXX,4,Hangup

exten => _81XXXXXXXXXX,1,AGI(agi://127.0.0.1:4577/call_log)
exten => _81XXXXXXXXXX,2,Dial(SIP/${EXTEN:1}@Xcast_OutBound,,tTo)
exten => _81XXXXXXXXXX,3,Hangup

[williamconley]

If you modify your terminology slightly, you'll have more fun. Instead of calling them "Transfers" (which could also be construed to mean a transfer from one agent to another agent, which does not involve a carrier normally), consider calling it a 3-way call. Then you may find that the 3-way call dial prefix for your campaign is related to your question. If, that is, your version of Vicidial has such an option.

Which brings me to the next point: You obviously tried to list your system specifications, but you missed the most important pieces.

1) Your Vicidial Version With Build (you missed the With Build)
2) GoAutoDial is your installer, and comes in more than one version. You did not list the version of the installer.

As such, to help you out, here are our newbie suggestions again:

when you post, please post your entire configuration including (but not limited to) your installation method and vicidial version with build.

this IS a requirement for posting along with reading the stickies (at the top of each forum) and the manager's manual (available on EFLO.net, both free and paid versions)

You should also post: Asterisk version, telephony hardware (model number is helpful here), cluster information if you have one, and whether any other software is installed in the box. If your installation method is "from scratch" you must post your operating system and should also post the .iso version from which you installed your original operating system. If your installation is "Hosted" list the site name of the host.

If this is a "Cloud" or "Virtual" server, please note the technology involved along with the version of that techology (ie: VMware Server Version 2.0.2). If it is not, merely stating the Motherboard model # and CPU would be helpful.

Similar to This:

Vicibox X.X from .iso | Vicidial X.X.X-XXX Build XXXXXX-XXXX | Asterisk X.X.X | Single Server | No Digium/Sangoma Hardware | No Extra Software After Installation | Intel DG35EC | Core2Quad Q6600

Happy Hunting!