vicidial.org

Hi,

i am unable to make out going calls to Australia, i am getting the message of it is not a valid extension.
please help me.


Executing MeetMe("Local/8600051@default-2c0c,2", "8600051|F") in new stack
> Channel Local/8600051@default-2c0c,1 was answered.
== Starting Local/8600051@default-2c0c,1 at default,061390402340,1 failed so falling back to exten 's'
== Starting Local/8600051@default-2c0c,1 at default,s,1 still failed so falling back to context 'default'
-- Sent into invalid extension 's' in context 'default' on Local/8600051@default-2c0c,1
-- Executing Playback("Local/8600051@default-2c0c,1", "invalid") in new stack
-- Playing 'invalid' (language 'en')
Aug 6 02:30:21 WARNING[844]: file.c:1045 ast_waitstream: Unexpected control subclass '-1'
== Manager 'sendcron' logged off from 127.0.0.1
== Parsing '/etc/asterisk/manager.conf': Found
== Manager 'sendcron' logged on from 127.0.0.1
-- Executing DeadAGI("Local/8600051@default-2c0c,1", "agi://127.0.0.1:4577/call_log--HVcauses--PRI-----NODEBUG-----0---------------") in new stack
-- AGI Script agi://127.0.0.1:4577/call_log--HVcauses ... ---------- completed, returning 0
== Spawn extension (default, 8600051, 1) exited non-zero on 'Local/8600051@default-2c0c,2'
-- Executing DeadAGI("Local/8600051@default-2c0c,2", "agi://127.0.0.1:4577/call_log--HVcauses--PRI-----NODEBUG-----0---------------") in new stack
-- AGI Script agi://127.0.0.1:4577/call_log--HVcauses ... ---------- completed, returning 0

are you getting this message while logging in as agent or while dialling out ?

Did u changed your server ip recently ,?
if yes then did u run the ip update script?

what dialplan you are using to dial out , and check the autodial prefix and manual dial prefix used in the campaing.

default,061390402340

Do you have a carrier with a dialplan entry pattern that will match "061390402340"? (such as _06XXXXXXXXXX?)

Why the 0 + 11 digits? Seems like an odd pattern to me?

when you post, please post your entire configuration including (but not limited to) your installation method and vicidial version with build.

this IS a requirement for posting along with reading the stickies (at the top of each forum) and the manager's manual (available on EFLO.net, both free and paid versions)

You should also post: Asterisk version, telephony hardware (model number is helpful here), cluster information if you have one, and whether any other software is installed in the box. If your installation method is "from scratch" you must post your operating system and should also post the .iso version from which you installed your original operating system. If your installation is "Hosted" list the site name of the host.

If this is a "Cloud" or "Virtual" server, please note the technology involved along with the version of that techology (ie: VMware Server Version 2.0.2). If it is not, merely stating the Motherboard model # and CPU would be helpful.

Similar to This:

Vicibox X.X from .iso | Vicidial X.X.X-XXX Build XXXXXX-XXXX | Asterisk X.X.X | Single Server | No Digium/Sangoma Hardware | No Extra Software After Installation | Intel DG35EC | Core2Quad Q6600

Hi,

after making the call only i will get the message of not a valid extension. and please send me dialplan of australia outging.

and i am using the version of asterisk:1.2.30.2

what dialplan you are using currenty?

as you r dialling 061390402340 so your dialplan should be

exten => _061X.,1,AGI(agi://127.0.0.1:4577/call_log)
exten => _061X.,2,Dial(${TESTSIPTRUNK}/${EXTEN:1},,tTor)
exten => _061X.,3,Hangup

note:
{EXTEN:1} will remove the first digit of the dialling no ie 0 will be removed

make sure in campaign u should put 0 as dialprefix and in upload lead should have 61 as phone code and phone field with exact no .

Hi,
after changing the dial plan and add the 0 in campaign dial prefix. its showing on agent screen call was live, but its automatically wrap-up and not connecting to destination phone call.

Executing MeetMe("Local/8600051@default-2320,2", "8600051|F") in new stack
> Channel Local/8600051@default-2320,1 was answered.
-- Executing AGI("Local/8600051@default-2320,1", "agi://127.0.0.1:4577/call_log") in new stack
-- AGI Script agi://127.0.0.1:4577/call_log completed, returning 0
-- Executing Dial("Local/8600051@default-2320,1", "SIP/siptrunk/61390402340||tTor") in new stack
-- Called siptrunk/61390402340
== Manager 'sendcron' logged off from 127.0.0.1
== Manager 'sendcron' logged off from 127.0.0.1
-- SIP/siptrunk-08355fc0 is making progress passing it to Local/8600051@default-2320,1
-- SIP/siptrunk-08355fc0 answered Local/8600051@default-2320,1
Aug 7 04:30:19 WARNING[8285]: channel.c:2781 ast_channel_make_compatible: No path to translate from Local/8600051@default-2320,1(64) to SIP/siptrunk-08355fc0(256)
Aug 7 04:30:19 WARNING[8285]: app_dial.c:1628 dial_exec_full: Had to drop call because I couldn't make Local/8600051@default-2320,1 compatible with SIP/siptrunk-08355fc0
== Spawn extension (default, 061390402340, 2) exited non-zero on 'Local/8600051@default-2320,1'
-- Executing DeadAGI("Local/8600051@default-2320,1", "agi://127.0.0.1:4577/call_log--HVcauses--PRI-----NODEBUG-----16---------------") in new stack
-- AGI Script agi://127.0.0.1:4577/call_log--HVcauses ... ---------- completed, returning 0
== Spawn extension (default, 8600051, 1) exited non-zero on 'Local/8600051@default-2320,2'
-- Executing DeadAGI("Local/8600051@default-2320,2", "agi://127.0.0.1:4577/call_log--HVcauses--PRI-----NODEBUG-----0---------------") in new stack
-- AGI Script agi://127.0.0.1:4577/call_log--HVcauses ... ---------- completed, returning 0

what codec your provider supports.

if g729 then install and enable in the carrier

yes, i installed the g729 codecs. but same problem

get the output of
show translation

in carrier setting did u enter
disallow=all
allow=g729

make sure your provider supports g729 or someother codec

yes, i given has you mentioned. for manual dialing i put the 061and number

are you able to dial manually from the softphone ( not fromthe agent screen)

ask your provider in which format u need to dial
like : countrycode+ mobileno or 0+code+number

previously we dialed 0+code+number(061number). it was worked previously

these are the warnings i am getting


SIP/siptrunk-08399b68 answered Local/8600051@default-c60b,1
Aug 7 05:05:40 WARNING[16881]: channel.c:2781 ast_channel_make_compatible: No path to translate from Local/8600051@default-c60b,1(64) to SIP/siptrunk-08399b68(256)
Aug 7 05:05:40 WARNING[16881]: app_dial.c:1628 dial_exec_full: Had to drop call because I couldn't make Local/8600051@default-c60b,1 compatible with SIP/siptrunk-08399b68
== Spawn extension (default, 061385668410, 2) exited non-zero on 'Local/8600051@default-c60b,1'

type the following command in the asterisk cli and let me know the output
show translation

g723 gsm ulaw alaw g726 adpcm slin lpc10 g729 speex ilbc
g723 - - - - - - - - - - -
gsm - - 2 2 2 2 1 2 - 13 -
ulaw - 2 - 1 2 2 1 2 - 13 -
alaw - 2 1 - 2 2 1 2 - 13 -
g726 - 2 2 2 - 2 1 2 - 13 -
adpcm - 2 2 2 2 - 1 2 - 13 -
slin - 1 1 1 1 1 - 1 - 12 -
lpc10 - 2 2 2 2 2 1 - - 13 -
g729 - - - - - - - - - - -
speex - 2 2 2 2 2 1 2 - - -
ilbc - - - - - - - - - - -

g729 not installed

or just change to ulaw

disallow=all
allow=ulaw

yes, iam installing the g729 and given allow=ulaw also. but from soft phone i dialed the outgoing number(061XXXXXXXXX), its ringing in soft phone, but not connecting to the phone(destination).

what do you mean by "not connecting to"? do you mean not ringing? (asterisk CLI output will help troubleshoot that) or no sound when you answer? (which would be the codec g729 vs ulaw, you are already working on resolving ... ).

also of note: please do not ignore this request, I will post it again, please try to get this information:

when you post, please post your entire configuration including (but not limited to) your installation method and vicidial version with build.

this IS a requirement for posting along with reading the stickies (at the top of each forum) and the manager's manual (available on EFLO.net, both free and paid versions)

You should also post: Asterisk version, telephony hardware (model number is helpful here), cluster information if you have one, and whether any other software is installed in the box. If your installation method is "from scratch" you must post your operating system and should also post the .iso version from which you installed your original operating system. If your installation is "Hosted" list the site name of the host.

If this is a "Cloud" or "Virtual" server, please note the technology involved along with the version of that techology (ie: VMware Server Version 2.0.2). If it is not, merely stating the Motherboard model # and CPU would be helpful.

Similar to This:

Vicibox X.X from .iso | Vicidial X.X.X-XXX Build XXXXXX-XXXX | Asterisk X.X.X | Single Server | No Digium/Sangoma Hardware | No Extra Software After Installation | Intel DG35EC | Core2Quad Q6600

when i am making call to australia, it is dial. but call was not ringing suddenly it is DeadAGI. why it is happened please help me. and check the bellow information.




Executing MeetMe("Local/8600051@default-c151,2", "8600051|F") in new stack
> Channel Local/8600051@default-c151,1 was answered.
-- Executing AGI("Local/8600051@default-c151,1", "agi://127.0.0.1:4577/call_log") in new stack
-- AGI Script agi://127.0.0.1:4577/call_log completed, returning 0
-- Executing Dial("Local/8600051@default-c151,1", "SIP/siptrunk/61390402340||tTor") in new stack
-- Called siptrunk/61390402340
== Manager 'sendcron' logged off from 127.0.0.1
-- SIP/siptrunk-0846f1b8 answered Local/8600051@default-c151,1
== Spawn extension (default, 061390402340, 2) exited non-zero on 'Local/8600051@default-c151,1'
-- Executing DeadAGI("Local/8600051@default-c151,1", "agi://127.0.0.1:4577/call_log--HVcauses--PRI-----NODEBUG-----16-----ANSWER-----9-----0") in new stack
-- AGI Script agi://127.0.0.1:4577/call_log--HVcauses ... ---9-----0 completed, returning 0
== Spawn extension (default, 8600051, 1) exited non-zero on 'Local/8600051@default-c151,2'
-- Executing DeadAGI("Local/8600051@default-c151,2", "agi://127.0.0.1:4577/call_log--HVcauses--PRI-----NODEBUG-----0---------------") in new stack
-- AGI Script agi://127.0.0.1:4577/call_log--HVcauses ... ---------- completed, returning 0

Hi Raju,

Have you try do dial different number? like 61298757100(this is mcdonalds number =)) or any number in australia to test if you
can get the positive result?

Cheers
q^_6p

HI.

TRY :Omit Phone Code to Y if it's N in compaign detail.

unless you have properly loaded your phone code which should include anything other than the phone number that your Carrier will require to make the call (1 or 0 in some cases, perhaps a country code in some cases, perhaps 0011 then the country code ... etc).