vicidial.org

Hello all, I found "chan_zap.c:1072 zt_open: Unable to specify channel 1: No such device or address" when I try to start Asterisk after I install Digium TE110P Pri card. Any one help? Million thanks!

The output of ztcfg
=======================
ztcfg -vvvvv
Notice: Configuration file is /etc/zaptel.conf
line 269: Unable to read Zaptel version information.

Zaptel Version: Unknown
Echo Canceller: Unknown
Configuration
======================

SPAN 1: CCS/HDB3 Build-out: 0 db (CSU)/0-133 feet (DSX-1)

Channel map:

Channel 01: Clear channel (Default) (Slaves: 01)
Channel 02: Clear channel (Default) (Slaves: 02)
Channel 03: Clear channel (Default) (Slaves: 03)
Channel 04: Clear channel (Default) (Slaves: 04)
Channel 05: Clear channel (Default) (Slaves: 05)
Channel 06: Clear channel (Default) (Slaves: 06)
Channel 07: Clear channel (Default) (Slaves: 07)
Channel 08: Clear channel (Default) (Slaves: 08)
Channel 09: Clear channel (Default) (Slaves: 09)
Channel 10: Clear channel (Default) (Slaves: 10)
Channel 11: Clear channel (Default) (Slaves: 11)
Channel 12: Clear channel (Default) (Slaves: 12)
Channel 13: Clear channel (Default) (Slaves: 13)
Channel 14: Clear channel (Default) (Slaves: 14)
Channel 15: Clear channel (Default) (Slaves: 15)
Channel 16: D-channel (Default) (Slaves: 16)
Channel 17: Clear channel (Default) (Slaves: 17)
Channel 18: Clear channel (Default) (Slaves: 18)
Channel 19: Clear channel (Default) (Slaves: 19)
Channel 20: Clear channel (Default) (Slaves: 20)
Channel 21: Clear channel (Default) (Slaves: 21)
Channel 22: Clear channel (Default) (Slaves: 22)
Channel 23: Clear channel (Default) (Slaves: 23)
Channel 24: Clear channel (Default) (Slaves: 24)
Channel 25: Clear channel (Default) (Slaves: 25)
Channel 26: Clear channel (Default) (Slaves: 26)
Channel 27: Clear channel (Default) (Slaves: 27)
Channel 28: Clear channel (Default) (Slaves: 28)
Channel 29: Clear channel (Default) (Slaves: 29)
Channel 30: Clear channel (Default) (Slaves: 30)
Channel 31: Clear channel (Default) (Slaves: 31)

31 channels to configure.

ZT_CHANCONFIG failed on channel 1: Inappropriate ioctl for device (25)
====================================
The output of lspci -v
===================================
00:0a.0 Network controller: Tiger Jet Network Inc. Tiger3XX Modem/ISDN interface
Subsystem: Unknown device 79de:0001
Flags: bus master, medium devsel, latency 32, IRQ 21
I/O ports at c800 [size=256]
Memory at ed104000 (32-bit, non-prefetchable) [size=4K]
Capabilities: [40] Power Management version 2
====================================
The out output of cat /proc/zaptel/*
====================================
Span 1: WCT1/0 "Digium Wildcard TE110P T1/E1 Card 0" HDB3/CCS

1 WCT1/0/1
2 WCT1/0/2
3 WCT1/0/3
4 WCT1/0/4
5 WCT1/0/5
6 WCT1/0/6
7 WCT1/0/7
8 WCT1/0/8
9 WCT1/0/9
10 WCT1/0/10
11 WCT1/0/11
12 WCT1/0/12
13 WCT1/0/13
14 WCT1/0/14
15 WCT1/0/15
16 WCT1/0/16
17 WCT1/0/17
18 WCT1/0/18
19 WCT1/0/19
20 WCT1/0/20
21 WCT1/0/21
22 WCT1/0/22
23 WCT1/0/23
24 WCT1/0/24
25 WCT1/0/25
26 WCT1/0/26
27 WCT1/0/27
28 WCT1/0/28
29 WCT1/0/29
30 WCT1/0/30
31 WCT1/0/31
================================

love to, but this is an asterisk / vendor issue. after it's a working trunk we'll help like crazy, but ... well, hopefully someone will see your post and have had the identical problem and have a solution for you. otherwise, you are really best off calling your vendor or searching the general asterisk forums (there are more users of Asterisk than Vicidial by an order of magnitude, you have a much better chance of solving an asterisk issue there than here just like you have a much better chance of finding a mechanic to fix your transmission in a city with over a million residents rather than one with 800).

that being said ... did you load zaptel or ztdummy?

if this is a vicibox install ... reinstall WITH the card in place already so the system can recognize it during install.

Million thanks for your reply. I had correct this issue. It is ISDN parameters problem at zaptel.conf. My experience is you need to adjust every configuration parameters in that file to apply with the setting at ISDN side. It is working fine now. Thanks!