Configuring X100P card

[lexer]

Hi

I'm newbie with vicidial, I installed vicidial v.8.1.2, this version has:
OpenSuSE Leap v.42.3 64-bit
Kernel v.4.4.155
Asterisk v.13.21.1-vici
DAHDI v.2.11.1
LibPRI v.1.6.0
Amfletec VoiceSync v.1.3.8
OpenR2 v.1.3.3 for MFC/R2 support
ViciDial SVN v.2.14-689a build 180922-0958 revision 3035

I've installed a FXO X100P card the on the server, I see that viciduial linux OpenSuSE detected the card, because when I use the comand "lspci -v" on linux, it shows the card:

03:02.0 Communication controller: Tiger Jet Network Inc. Tiger3XX Modem/ISDN interface
Subsystem: Intel Corporation Digium X100P/X101P analogue PSTN FXO interface
Flags: bus master, medium devsel, latency 64, IRQ 11
I/O ports at de00 [size=256]
Memory at fd9ff000 (32-bit, non-prefetchable) [size=4K]
Capabilities: [40] Power Management version 2
Kernel modules: netjet, hisax, wcfxo

But It seems the vicidal DAHDI library doesn't recognized the card, because files system.conf and chan_dahdi.conf are empty:
This is the file system.conf located in /etc/dahdi/:

Code: Select all

# Autogenerated by /usr/sbin/dahdi_genconf on Tue Apr  2 05:19:30 2019
# If you edit this file and execute /usr/sbin/dahdi_genconf again,
# your manual changes will be LOST.
# Dahdi Configuration File
#
# This file is parsed by the Dahdi Configurator, dahdi_cfg
#
# Global data

loadzone        = us
defaultzone     = us


This is the file dahdi-channels.conf located in /etc/asterisk/:

Code: Select all

; Autogenerated by /usr/sbin/dahdi_genconf on Tue Apr  2 05:19:30 2019
; If you edit this file and execute /usr/sbin/dahdi_genconf again,
; your manual changes will be LOST.
; Dahdi Channels Configurations (chan_dahdi.conf)
;
; This is not intended to be a complete chan_dahdi.conf. Rather, it is intended
; to be #include-d by /etc/chan_dahdi.conf that will include the global settings
;


I've worked with pure asterisk and I use the command "dahdi_genconf" for generating the files system.conf and chan_dahdi.conf and detecting Dahdi channels, the issue is that the command shows only this:

Code: Select all

dahdi_genconf
Empty configuration -- no spans
Empty configuration -- no spans
Empty configuration -- no spans


Please, How can I make the vicidial to recognize the X100P card? do I have to reinstall or update DAHDI libreries?

[mflorell]

I haven't touched one of those in over a decade, and the last time I did, I had issues getting it to work properly. Also, analog lines don't work well at all with VICIdial.

[williamconley]

1) Install the card Before installing Vicidial. (IE: Start over and see if the system auto-configures the card at all)

2) Asterisk questions. Unrelated to Vicidial, per se. If you work with forums dealing directly with that card, you'll find out how to configure it with Asterisk. Once it works with asterisk we can help you make it work with Vicidial. Do note that a single line card has some extreme limitations. ONLY use this if you have no internet access available to use a VoIP telephone carrier.

[lexer]

Thanks for your answers

1) The card was in the server when I installed Vicidal

2)I already tried the X100P card on pure Asterisk and It worked, can I reinstall Dadhi libreries or update them for trying to make vicidial recognize the card?

[williamconley]

you would do better to find the differences between this asterisk and the other asterisk that worked (troubleshooting). of course, you might get lucky. the -vici version of asterisk has very small modifications to the source from "stock", so it won't be a vicidial source code alteration.