motorola x100p chipset installation failed.

All installation and configuration problems and questions

Moderators: gerski, enjay, williamconley, Op3r, Staydog, gardo, mflorell, MJCoate, mcargile, Kumba, Michael_N

motorola x100p chipset installation failed.

Postby gerski » Wed Aug 16, 2006 11:03 pm

here is the output when i check my motoroloa x100p

root@dialer:/etc/asterisk# lspci
00:00.0 Host bridge: Intel Corporation 82865G/PE/P DRAM Controller/Host-Hub Interface (rev 02)
00:01.0 PCI bridge: Intel Corporation 82865G/PE/P PCI to AGP Controller (rev 02)
00:1d.0 USB Controller: Intel Corporation 82801EB/ER (ICH5/ICH5R) USB UHCI Controller #1 (rev 02)
00:1d.1 USB Controller: Intel Corporation 82801EB/ER (ICH5/ICH5R) USB UHCI Controller #2 (rev 02)
00:1d.2 USB Controller: Intel Corporation 82801EB/ER (ICH5/ICH5R) USB UHCI Controller #3 (rev 02)
00:1d.3 USB Controller: Intel Corporation 82801EB/ER (ICH5/ICH5R) USB UHCI Controller #4 (rev 02)
00:1d.7 USB Controller: Intel Corporation 82801EB/ER (ICH5/ICH5R) USB2 EHCI Controller (rev 02)
00:1e.0 PCI bridge: Intel Corporation 82801 PCI Bridge (rev c2)
00:1f.0 ISA bridge: Intel Corporation 82801EB/ER (ICH5/ICH5R) LPC Interface Bridge (rev 02)
00:1f.1 IDE interface: Intel Corporation 82801EB/ER (ICH5/ICH5R) IDE Controller (rev 02)
00:1f.2 IDE interface: Intel Corporation 82801EB (ICH5) SATA Controller (rev 02)
00:1f.3 SMBus: Intel Corporation 82801EB/ER (ICH5/ICH5R) SMBus Controller (rev 02)
00:1f.5 Multimedia audio controller: Intel Corporation 82801EB/ER (ICH5/ICH5R) AC'97 Audio Controller (rev 02)
02:00.0 VGA compatible controller: nVidia Corporation NV5M64 [RIVA TNT2 Model 64/Model 64 Pro] (rev 15)
02:02.0 Modem: Motorola: Unknown device 3052 (rev 04)
02:03.0 Ethernet controller: 3Com Corporation 3c905C-TX/TX-M [Tornado] (rev 78)

in dmesg
ACPI: PCI Interrupt 0000:02:03.0[A] -> GSI 19 (level, low) -> IRQ 17
Zapata Telephony Interface Registered on major 196
Zaptel Version: 1.2.6 Echo Canceller: KB1

but when i type
modprobe zaptel
modprobe wcfxo

nothing happen.
root@dialer:/etc/asterisk# /sbin/ztcfg -vvvvvvvvvvvv

Zaptel Configuration
======================


Channel map:

Channel 01: FXS Kewlstart (Default) (Slaves: 01)

1 channels configured.

ZT_CHANCONFIG failed on channel 1: No such device or address (6)

how can i install my motorola x100p chipset to install properly.

i also enable my CRC CITT in my kernel and my asterisk does not booting properly


[chan_zap.so] => (Zapata Telephony w/PRI)
== Parsing '/etc/asterisk/zapata.conf': Found
Aug 17 12:02:07 WARNING[14193]: chan_zap.c:923 zt_open: Unable to specify channel 1: No such device or address
Aug 17 12:02:07 ERROR[14193]: chan_zap.c:6883 mkintf: Unable to open channel 1: No such device or address
here = 0, tmp->channel = 1, channel = 1
Aug 17 12:02:07 ERROR[14193]: chan_zap.c:10319 setup_zap: Unable to register channel '1-2'
Aug 17 12:02:07 WARNING[14193]: loader.c:414 __load_resource: chan_zap.so: load_module failed, returning -1
Aug 17 12:02:07 WARNING[14193]: loader.c:554 load_modules: Loading module chan_zap.so failed!
gerski
 
Posts: 432
Joined: Fri Jul 14, 2006 6:21 am

Postby mflorell » Wed Aug 16, 2006 11:17 pm

This is more of an Asterisk-related issue for http://forums.digium.com , but what do you get when you run zttool?

Have you tried putting the card in a different PCI slot?

Have you contacted the vendor that you bought the card from?
mflorell
Site Admin
 
Posts: 18386
Joined: Wed Jun 07, 2006 2:45 pm
Location: Florida

Postby gerski » Thu Aug 17, 2006 1:38 am

i can't seem to ruin zttool installation. all is failed

in
NOTES: If you want to install zttool diagnostics you may need the newt package installed:
http://www.freedomphones.net/files/newt-0.51.6.tar.gz
ln -s /usr/lib/libnewt.so.0.51.6 /usr/lib/libnewt.so.0.51
then go to your zaptel folder and do 'make zttool'

is there something i need to configure before this?

now i've seen an error, i think this has something to do with the IRQ right?


02:02.0 Modem: Motorola: Unknown device 3052 (rev 04) (prog-if 00 [Generic])
Subsystem: Motorola: Unknown device 3020
Flags: bus master, stepping, medium devsel, latency 32, IRQ 16
Memory at feaef000 (32-bit, non-prefetchable) [size=4K]
I/O ports at b800 [size=256]
Capabilities: [80] Power Management version 2

00:1f.5 Multimedia audio controller: Intel Corporation 82801EB/ER (ICH5/ICH5R) AC'97 Audio Controller (rev 02)
Subsystem: Intel Corporation D865PERL mainboard
Flags: bus master, medium devsel, latency 0, IRQ 16
Memory at febff800 (32-bit, non-prefetchable) [size=512]
Memory at febff400 (32-bit, non-prefetchable) [size=256]
Capabilities: [50] Power Management version 2

i have not yet tried putting the card in different PCI slot.
gerski
 
Posts: 432
Joined: Fri Jul 14, 2006 6:21 am


Return to Support

Who is online

Users browsing this forum: Google [Bot] and 145 guests