vicidial.org

by **gmcust3** » Sun Apr 18, 2010 12:45 am

Anyone successfully Installed VoiceTime over VNow 1.3 with the steps mentioned by Sangoma ??

I tried but never been successful !!

Gardo, any write up on that ?

by **gardo** » Sun Apr 18, 2010 4:19 pm

Can you list the process you did?

by **gmcust3** » Sun Apr 18, 2010 9:42 pm

http://wiki.sangoma.com/wanpipe-linux-asterisk-install

You got any shell file which can install VoiceTime ?

by **gardo** » Mon Apr 19, 2010 3:06 pm

No shell file available yet.

That's not the proper link. Here is: http://wiki.sangoma.com/sangoma-wanpipe-voicetime. I think it's pretty much straight forward. Try it and post the process here.

by **brett05** » Tue Apr 20, 2010 8:56 am

for sangoma voice with vicidialnow your only solution is do a manual setup for zaptel or dahdi .
exemple as i know vicidialnow use zaptel 1.2 with asterisk 1.2 too but the zaptel is included directly in the img kernel .
so sangoma can not be installed .
this is my step for the sangoma and it will work.
mkdir /usr/src/tars
cd /usr/src/tars
wget wget http://downloads.digium.com/pub/zaptel/ ... .27.tar.gz
wget wget ftp://ftp.sangoma.com/linux/wanpipe_voi ... -1.0.9.tgz
tar -xzf /usr/src/tars/zaptel-1.2.27.tar.gz
tar -xzf /usr/src/tars/wanpipe-voicetime-1.0.9.tgz
cd /usr/src/zaptel-1.2.27
make clean
make
make install
make zttool
rm /etc/init.d/zaptel
rm /etc/rc.d/init.d/zaptel
# Install some VoiceTime!
cd /usr/src/wanpipe-voicetime-1.0.9
make ZAPDIR=/usr/src/zaptel-1.2.27/kernel
ok now here the wanpipe and zaptel are done we need just load the wanpipe at the boot server .
so nano /etc/rc.local
and add this line: ZAP_MOD=wanpipe_voicetime
and reboot your server

by **gardo** » Tue Apr 20, 2010 2:44 pm

Thank you for posting this.

by **gmcust3** » Wed Aug 18, 2010 7:59 am

cd: /usr/src/zaptel-1.2.27

SHOULD BE

cd: /usr/src/tars/zaptel-1.2.27

by **gmcust3** » Wed Aug 18, 2010 8:18 am

I did as suggested by Brett in above Post.

When I do

dmesg |grep USB

[root@vici ~]# dmesg |grep USB
drivers/usb/input/hid-core.c: v2.6:USB HID core driver
ehci_hcd 0000:00:10.4: new USB bus registered, assigned bus number 1
ehci_hcd 0000:00:10.4: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
hub 1-0:1.0: USB hub found
ohci_hcd: 2005 April 22 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI)
USB Universal Host Controller Interface driver v3.0
uhci_hcd 0000:00:10.0: new USB bus registered, assigned bus number 2
hub 2-0:1.0: USB hub found
uhci_hcd 0000:00:10.1: new USB bus registered, assigned bus number 3
hub 3-0:1.0: USB hub found
uhci_hcd 0000:00:10.2: new USB bus registered, assigned bus number 4
hub 4-0:1.0: USB hub found
uhci_hcd 0000:00:10.3: new USB bus registered, assigned bus number 5
hub 5-0:1.0: USB hub found
usb 3-2: new full speed USB device using uhci_hcd and address 2
[root@vici ~]#

USB Voice Time Not Installed ?

by **williamconley** » Wed Aug 18, 2010 8:37 pm

http://wiki.sangoma.com/sangoma-wanpipe-voicetime

did you run zttest?

by **gardo** » Thu Aug 19, 2010 1:33 pm

Try our latest ISO:

http://www.vicidialnow.nl/ftp/VicidialNOW/ISO/2.0/goautodial-ce-2.0-rc2.iso

Sangoma Wanpipe voice timer driver can be installed with 3 simple commands. It also has the following updated software:

Vicidial 2.2.1
Asterisk 1.4.27.1-vici
Dahdi
VtigerCRM 5.1.0
Sangoma 3.5.14

This is the last release candidate for the final 2.0 version coming very soon.

Out of the box support for the following:

1. Digium and Sangoma cards. (Sangoma voicetime can easily be installed with 3 simple commands - final release will have out of the box support too).
2. Vicidial and Vtiger synchronization

Please report any bugs or issues encountered.

by **gmcust3** » Thu Aug 19, 2010 1:38 pm

goautodial-ce-2.0-rc2.iso has Updated Vnow based Agent screen ?

by **gardo** » Thu Aug 19, 2010 1:53 pm

Not yet. Final release will have it.

by **williamconley** » Thu Aug 19, 2010 2:27 pm

download speed is 168K (at 3:30PMEST). not horrible.

by **gardo** » Fri Aug 20, 2010 2:04 pm

Courtesy of Kim Hoogenberg from http://www.hostingondemand.nl. Thanks Kim.

by **gardo** » Fri Aug 20, 2010 4:08 pm

@gmcust: I have a pre-built Sangoma wanpipe-voicetime RPM. It's compatible with goautodial-2.0-rc2.iso. You can get them here:

http://www.vicidialnow.nl/ftp/VicidialNOW/RPMS/2.0/wanpipe-voicetime-1.0.9-1.i386.rpm
http://www.vicidialnow.nl/ftp/VicidialNOW/RPMS/2.0/dkms-2.0.21.1-2.el5.scopserv.noarch.rpm

Installation:

rpm -ivh dkms-2.0.21.1-2.el5.scopserv.noarch.rpm
rpm -ivh --replacepkgs --replacefiles wanpipe-voicetime-1.0.9-1.i386.rpm

Usage:

modprobe wanpipe-voicetime

Let me know if it works for you.

by **gmcust3** » Fri Oct 22, 2010 2:01 am

I am still using ViciNow as I am YET to face any Issues with ViciNOW 1.3 Except Too many No answer.

For that I have VoiceTime Module

Can I use above steps for VNow 1.3 VoiceTime Installation ?

by **gmcust3** » Fri Oct 22, 2010 2:41 am

I am getting...

Preparing... ########################################### [100%]
1:dkms ########################################### [100%]
error: Failed dependencies:
dahdi-linux is needed by wanpipe-voicetime-1.0.9-1.i386
FATAL: Module wanpipe_voicetime not found.
[root@vici ~]#

by **gardo** » Fri Oct 22, 2010 4:18 pm

Looks like you need to replace Zaptel with Dahdi.

by **gmcust3** » Sat Oct 23, 2010 3:06 am

In VNow 1.3, where is the Zaptel folder ?

make ZAPDIR=/usr/src/zaptel-<ver>

by **gardo** » Mon Oct 25, 2010 11:47 am

VicidialNOW doesn't have the source files for Zaptel by default (unlike GoAutoDial). You need to download them manually from Digium.

by **gmcust3** » Sat Oct 30, 2010 8:01 am

I have downloaded Zaptel and Installed.

dmesg | grep USB Returns me :

drivers/usb/input/hid-core.c: v2.6:USB HID core driver
ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 1
ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
hub 1-0:1.0: USB hub found
ohci_hcd: 2005 April 22 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI)
USB Universal Host Controller Interface driver v3.0
uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 2
hub 2-0:1.0: USB hub found
uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 3
hub 3-0:1.0: USB hub found
uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 4
hub 4-0:1.0: USB hub found
uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus number 5
hub 5-0:1.0: USB hub found
usb 2-1: new full speed USB device using uhci_hcd and address 2

vici*CLI> zap show status
Description Alarms IRQ bpviol CRC4
ZTDUMMY/1 (source: RTC) 1 UNCONFIGUR 0 0 0
vici*CLI>

When my server is Booting I see ,

Zaptel Versin : Unknown
Echo Canceller : Unknown

Too many tones Included.
ioctl(ZT_LOADZONE) failed:
Line 10 : Unable to Register

Kindly advice.

by **gardo** » Sat Oct 30, 2010 2:16 pm

What version of Zaptel are you trying to install?

by **gmcust3** » Sat Oct 30, 2010 11:49 pm

zaptel-1.4.12.1

by **gardo** » Mon Nov 01, 2010 3:27 pm

Have you uninstalled the old Zaptel modules?

# rpm -qa | grep zaptel

This will list the Zaptel packages installed on the system. Uninstall them by running:

# rpm -e "name of package" --nodep

Reinstall Zaptel 1.4.12.1.

by **gmcust3** » Mon Nov 01, 2010 9:27 pm

[root@vici ~]# rpm -qa | grep zaptel
zaptel-modules-1.2.27-2.2.6.18_164.el5.vnow
zaptel-1.2.27-1
zaptel-devel-1.2.27-1

by **williamconley** » Mon Nov 01, 2010 9:52 pm

gardo wrote:Uninstall them by running:

# rpm -e "name of package" --nodep

Reinstall Zaptel 1.4.12.1.

by **gmcust3** » Tue Nov 02, 2010 3:04 am

zaptel-1.2.27-1 will be the name of the package ?

by **gardo** » Fri Nov 05, 2010 2:41 pm

zaptel-modules-1.2.27-2.2.6.18_164.el5.vnow
zaptel-1.2.27-1
zaptel-devel-1.2.27-1

Those are the names of the packages.

by **gmcust3** » Sat Nov 06, 2010 1:04 am

[root@vici ~]# rpm -qa | grep zaptel
zaptel-modules-1.2.27-2.2.6.18_164.el5.vnow
zaptel-1.2.27-1
zaptel-devel-1.2.27-1
[root@vici ~]# rpm -e zaptel-modules-1.2.27-2.2.6.18_164.e15.vnow --nodep
--nodep: unknown option
[root@vici ~]# rpm -e zaptel-modules-1.2.27-2.2.6.18_164.e15.vnow -nodep
-nodep: unknown option
[root@vici ~]# rpm -e "zaptel-modules-1.2.27-2.2.6.18_164.e15.vnow" --nodep
--nodep: unknown option
[root@vici ~]#

--nodep unknown Options ?

by **gardo** » Mon Nov 08, 2010 2:30 pm

Type error. Sorry bout that. Should be:

--nodeps

by **gmcust3** » Thu Nov 11, 2010 6:26 am

Btw, Sangoma Says It shld also work with Zaptel 1.2 !!

Any Advice on it ?

vicidial.org

VoiceTime and VNow 1.3 and Steps mentioned in Sangoma

VoiceTime and VNow 1.3 and Steps mentioned in Sangoma

thanks

Who is online