Vicibox--2.4|Vicidial VERSION: 2.4-294 BUILD: 101227-1320|Asterisk 1.4.21.2|Single Server|Sangoma A104d QUAD T1/E1 AFT card|No extra software.
Linux OS: Linux vici2 2.6.18-128.el5PAE
OS installation method: Via ISO image
We have two Sangoma A104 Quad cards installed in the system with 8 E1 PRI's. We were trying to set up an outbound auto dial campaign with the following settings
Auto Dial level =1
Dial Method = Ratio
Hopper Level=100
Remote Agent line = 240
Trunks=120
Max calls per second =20
Before running the campaign, we ran a small with only one outdial number in the lead file. During this test, when the outdial call was ringing on the handset, we could see 3 active channels in asterisk (asterisk -rx "core show channels verbose"), as shown below
localhost*CLI> core show channels verbose
Channel Context Extension Prio State Application Data CallerID Duration Accountcode BridgedTo
Zap/1-1 from-pstn 919971592510 1 Ringing AppDial (Outgoing Line) 0000000000 00:00:08 (None)
Local/919971592510@d default 919971592510 2 Ring Dial ZAP/g1/09899139108|30|o 0000000000 00:00:08 (None)
Local/919971592510@d default 919971592510 1 Down (None) (None) 0000000000 00:00:08 (None)
3 active channels
1 active call
However for the split second when the user picked up the call to the time the prompt playback started, we could see the Active channels and active calls shifting from 2 to 1, as given below
localhost*CLI> core show channels verbose
Channel Context Extension Prio State Application Data CallerID Duration Accountcode BridgedTo
Local/919971592510@d default h 1 Up DeadAGI agi://127.0.0.1:4577/call 0000000000 00:00:16 (None)
Zap/1-1 default 8367 2 Up AGI agi://127.0.0.1:4577/call 0000000000 00:00:16 (None)
2 active channels
2 active calls
localhost*CLI> core show channels verbose
Channel Context Extension Prio State Application Data CallerID Duration Accountcode BridgedTo
Zap/1-1 default 8367 4 Up Playback test 00:00:20 (None)
1 active channel
To summarize, when the call was ringing, there were 3 channels, once the call was picked up there were 2 channels and immediately afterwards, when the prompt played there was only 1 active channel. Can you please shed some light as to what is going on here or there is some issue in my extensions.conf file shown below. We also found some delay in the playing of the prompt after the user picked up the phone, ranging from 5 seconds on some handsets to around 19 seconds in other handsets, when we finally ran the campaign. What could be going wrong here
[general]
static=yes
writeprotect=no
clearglobalvars=no
exten=>_91XXXXXXXXXX,1,AGI(agi://127.0.0.1:4577/call_log)
exten=>_91XXXXXXXXXX,n,Dial(ZAP/g1/0${EXTEN:2}|30,o)
exten=>_91XXXXXXXXXX,n,Hangup()
exten=>8367,1,Playback(sip-silence)
exten=>8367,n,AGI(agi://127.0.0.1:4577/call_log)
exten=>8367,n,AGI(agi-VDAD_ALL_outbound.agi,BROADCAST-----SO)
exten=>8367,n,Playback(test)
exten=>8367,n,Hangup
exten=>h,1,DeadAGI(agi://127.0.0.1:4577/call_log--HVcauses ... EBUG-----${HANGUPCAUSE}-----${DIALSTATUS}-----${DIALEDTIME}-----${ANSWEREDTIME})
****************************************************
[root@localhost asterisk]# crontab -l
###live script for astguiclient processes
#* * * * * /usr/share/astguiclient/ADMIN_keepalive_ALL.pl
### kill Hangup script for Asterisk updaters
#* * * * * /usr/share/astguiclient/AST_manager_kill_hung_congested.pl
### updater for voicemail
##* * * * * /usr/share/astguiclient/AST_vm_update.pl
### updater for conference validator
#* * * * * /usr/share/astguiclient/AST_conf_update.pl
### flush queue DB table every hour for entries older than 1 hour
#11 * * * * /usr/share/astguiclient/AST_flush_DBqueue.pl -q
### fix the vicidial_agent_log once every hour and the full day run at night
#33 * * * * /usr/share/astguiclient/AST_cleanup_agent_log.pl
#50 0 * * * /usr/share/astguiclient/AST_cleanup_agent_log.pl --last-24hours
## uncomment below if using QueueMetrics
##*/5 * * * * /usr/share/astguiclient/AST_cleanup_agent_log.pl --only-qm-live-call-check
## uncomment below if using Vtiger
##1 1 * * * /usr/share/astguiclient/Vtiger_optimize_all_tables.pl --quiet
### updater for VICIDIAL hopper
#* * * * * /usr/share/astguiclient/AST_VDhopper.pl -q
### adjust the GMT offset for the leads in the vicidial_list table
##1 1,7 * * * /usr/share/astguiclient/ADMIN_adjust_GMTnow_on_leads.pl --debug
### reset several temporary-info tables in the database
#2 1 * * * /usr/share/astguiclient/AST_reset_mysql_vars.pl
### optimize the database tables within the asterisk database
#3 1 * * * /usr/share/astguiclient/AST_DB_optimize.pl
### VICIDIAL agent time log weekly and daily summary report generation
#2 0 * * 0 /usr/share/astguiclient/AST_agent_week.pl
#22 0 * * * /usr/share/astguiclient/AST_agent_day.pl
### VICIDIAL campaign export scripts (OPTIONAL)
##32 0 * * * /usr/share/astguiclient/AST_VDsales_export.pl
##42 0 * * * /usr/share/astguiclient/AST_sourceID_summary_export.pl
### remove old recordings more than 7 days old
##24 0 * * * /usr/bin/find /var/spool/asterisk/monitorDONE -maxdepth 2 -type f -mtime +7 -print | xargs rm -f
### roll logs monthly on high-volume dialing systems
##30 1 1 * * /usr/share/astguiclient/ADMIN_archive_log_tables.pl
### remove old vicidial logs and asterisk logs more than 2 days old
#28 0 * * * /usr/bin/find /var/log/astguiclient -maxdepth 1 -type f -mtime +2 -print | xargs rm -f
#29 0 * * * /usr/bin/find /var/log/asterisk -maxdepth 3 -type f -mtime +2 -print | xargs rm -f
#30 0 * * * /usr/bin/find / -maxdepth 1 -name "screenlog.0*" -mtime +4 -print | xargs rm -f
*******************************************************
Prompt playback delay Outbound Auto Dial
Moderators: gerski, enjay, williamconley, Op3r, Staydog, gardo, mflorell, MJCoate, mcargile, Kumba, Michael_N
13 posts
• Page 1 of 1
Prompt playback delay Outbound Auto Dial
by richie.gbpec » Fri Jan 14, 2011 9:20 am
- richie.gbpec
- Posts: 19
- Joined: Tue Jan 04, 2011 7:43 am
by williamconley » Fri Jan 14, 2011 3:01 pm
let me start by thanking you for posting your detailed installation specs.
but: there is no vicibox 2.4 (vicibox is the installer, it's probably more like vicibox 3.0.9?) it's in the ssh splash screen when you log in.
installation is always via .iso, i just like having the name or version of the .iso (ie: back to vicibox 3.0.9). unless you install from a USB stick or netboot, you installed from an .iso
(I'm just pickin on you a little, don't take it the wrong way, trying to be detailed and perhaps a little CDO).
Now that my fun is done:
Ultimately your complaint is slow to play sounds, right?
Please list your server load (and CPU specs for comparison); the number of simultaneous calls when this occurs; when you ran with one call during testing did this occur? (you omitted the RESULT of the test, but did imply it ... i never assume); also try a dahdi timing test (dahdi_test at cli)
also: if your system has a total of 120 trunks ... i'm not sure it's appropriate to have 240 "agent lines". are you talking about a "remote agent" in the remote agent settings, with the "lines" set to 240? Obviously impossible to fill 240 agent lines with 120 trunks available.
but: there is no vicibox 2.4 (vicibox is the installer, it's probably more like vicibox 3.0.9?) it's in the ssh splash screen when you log in.
installation is always via .iso, i just like having the name or version of the .iso (ie: back to vicibox 3.0.9). unless you install from a USB stick or netboot, you installed from an .iso
(I'm just pickin on you a little, don't take it the wrong way, trying to be detailed and perhaps a little CDO).
Now that my fun is done:
Ultimately your complaint is slow to play sounds, right?
Please list your server load (and CPU specs for comparison); the number of simultaneous calls when this occurs; when you ran with one call during testing did this occur? (you omitted the RESULT of the test, but did imply it ... i never assume); also try a dahdi timing test (dahdi_test at cli)
also: if your system has a total of 120 trunks ... i'm not sure it's appropriate to have 240 "agent lines". are you talking about a "remote agent" in the remote agent settings, with the "lines" set to 240? Obviously impossible to fill 240 agent lines with 120 trunks available.
Vicidial Installation and Repair, plus Hosting and Colocation
Newest Product: Vicidial Agent Only Beep - Beta
http://www.PoundTeam.com # 352-269-0000 # +44(203) 769-2294
Newest Product: Vicidial Agent Only Beep - Beta
http://www.PoundTeam.com # 352-269-0000 # +44(203) 769-2294
- williamconley
- Posts: 20258
- Joined: Wed Oct 31, 2007 4:17 pm
- Location: Davenport, FL (By Disney!)
by richie.gbpec » Fri Jan 21, 2011 8:37 am
VERSION: 2.2.1-237
BUILD: 100510-2015
Asterisk 1.4.38-vici
Dahdi -2.2.4 complete version
kernel 2.6.18-128.el5PAE
RHEL v 5.3 (32 bit)
Sangoma cards = 2 (A104d QUAD T1/E1 AFT card each), No extra software
PRI's = 8
Campaign Settings:
auto dial level= 10
hopper level= 500
dial time out= 60
Max VICIDIAL Trunks= 240
Max Calls per Second= 4/sec
Remote agent Lines : 24
Leads file has 5000 leads
We did two Auto dial Outbound survey campaign with the above configuration. In the first test, we used the following extensions.conf
[general]
static=yes
writeprotect=no
[default]
exten=>_91XXXXXXXXXX,1,Dial(DAHDI/g1/0${EXTEN:2},30|o)
exten=>_91XXXXXXXXXX,n,Hangup()
; VICIDIAL_auto_dialer transfer script SURVEY at beginning:
;exten => 8366,1,AGI(agi://127.0.0.1:4577/call_log)
exten => 8366,n,Playback(welcome_tofrenzo_the_best_way_english)
exten => 8366,n,Hangup
;exten => h,1,DeadAGI(agi://127.0.0.1:4577/call_log--HVcauses ... EBUG-----${HANGUPCAUSE}-----${DIALSTATUS}-----${DIALEDTIME}-----${ANSWEREDTIME})
If you would notice, we had removed most of the exten provided by vicidial and the prompt playback was defined in the extensions.conf. We were able to complete the campaign in around 30 minutes with no perceptible delay in prompt playback when users answered the call.
We ran the same auto dial outbound survey campaign with the same campaign setting as above, but using extensions.conf which you get on installing vicidial (extensions.conf is given at the bottom)
However, we got perceptible delay in prompt playback ranging from 5 to 12 seconds when users answered the call.
On monitoring the master.csv for this test run showed delay on those numbers where the delay was noticed. For instance, you can see below that the call got transfered from local channel to dahdi channel in 5 seconds, which was also the delay in prompt playback on answering the call by this user
"","0000000000","919651363002","default","""V0120124232000000220"" <0000000000>","Local/919651363002@default-8196,2","DAHDI/29-1","Dial","DAHDI/g1/09651363002|30|o","2011-01-20 07:13:12","2011-01-20 07:13:41","2011-01-20 07:13:46",34,5,"ANSWERED","DOCUMENTATION","1295507592.633",""
We did not see any such delay in master.csv when we ran the first test. What could be going wrong here. Do you think the following extra entries under "VICIDIAL_auto_dialer transfer script SURVEY at beginning" causing this delay. If not, then what are they doing, I never used them in the first test and got good result. This is just a conjecture and curious to know what is going wrong.
exten => 8366,2,AGI(agi://127.0.0.1:4577/call_log)
exten => 8366,3,AGI(agi-VDAD_ALL_outbound.agi,SURVEYCAMP-----LB)
exten => 8366,4,AGI(agi-VDAD_ALL_outbound.agi,SURVEYCAMP-----LB)
extensions.conf for second test
[general]
static=yes
writeprotect=no
[globals]
CONSOLE=Console/dsp ; Console interface for demo
TRUNK=Zap/r1 ; Trunk interface
TRUNKX=Zap/r2 ; 2nd trunk interface
TRUNKIAX=IAX2/ASTtest1:test@10.10.10.16:4569 ; IAX trunk interface
TRUNKIAX1=IAX2/ASTtest1:test@10.10.10.16:4569 ; IAX trunk interface
TRUNKBINFONE=IAX2/1112223333:PASSWORD@iax.binfone.com ; IAX trunk interface
SIPtrunk=SIP/1234:PASSWORD@sip.provider.net ; SIP trunk
#include extensions-vicidial.conf
[trunkinbound]
; DID call routing process
exten => _X.,1,AGI(agi-DID_route.agi)
; FastAGI for VICIDIAL/astGUIclient call logging
exten => h,1,DeadAGI(agi://127.0.0.1:4577/call_log--HVcauses ... EBUG-----${HANGUPCAUSE}-----${DIALSTATUS}-----${DIALEDTIME}-----${ANSWEREDTIME})
[loopback-no-log]
; This context is to accept calls that have already been logged in another context in Vicidial
; and has been sent through one of the loopbacks. This is why this context is missing the h extension.
; Do not put any extensions in this context unless you specifically understand what this means.
;exten => _91NXXNXXXXXX,1,Dial(${TRUNKX}/${EXTEN:1},,To)
;exten => _91NXXNXXXXXX,n,Hangup
; special Canadian PRI callerIDname settings FOR USE IN LOOPBACK CONTEXT ONLY
;exten => _91NXXNXXXXXX,1,Set(CALLERID(name)="ACME Widgets")
;exten => _91NXXNXXXXXX,n,AGI(agi-CANADA_PRI_CIDname.agi)
;exten => _91NXXNXXXXXX,n,Dial(${TRUNKX}/${EXTEN:1},,To)
;exten => _91NXXNXXXXXX,n,Hangup
exten => _999XX11112,1,Wait(2)
exten => _999XX11112,n,Answer
exten => _999XX11112,n,Playback(ss-noservice)
exten => _999XX11112,n,Playback(vm-goodbye)
exten => _999XX11112,n,Hangup
[default]
include => vicidial-auto
exten=>_91XXXXXXXXXX,1,AGI(agi://127.0.0.1:4577/call_log)
exten=>_91XXXXXXXXXX,n,Dial(DAHDI/g1/0${EXTEN:2},30|o)
exten=>_91XXXXXXXXXX,n,Hangup()
; VICI-GROUP DIRECT SUPPORT LINE (VICIHELP[84244357])
exten => _84244XXX,1,Dial(IAX2/vicihelp/${EXTEN:5})
; Local agent alert extensions
exten => _8600XXX*.,1,AGI(agi-VDADfixCXFER.agi)
exten => _78600XXX*.,1,AGI(agi-VDADfixCXFER.agi)
; Local blind monitoring
exten => _08600XXX,1,Dial(${TRUNKblind}/6${EXTEN:1},55,To)
; playback of recorded prompts
exten => _851XXXXX,1,Answer
exten => _851XXXXX,2,Playback(${EXTEN})
exten => _851XXXXX,3,Hangup
; this is used for playing a message to an answering machine forwarded from AMD in VICIDIAL
exten => _7851XXXXX,1,WaitForSilence(2000,2) ; AMD got machine. leave message after recording
exten => _7851XXXXX,2,Playback(${EXTEN:1})
exten => _7851XXXXX,3,AGI(VD_amd_post.agi,${EXTEN:1})
exten => _7851XXXXX,4,Hangup
; FastAGI for VICIDIAL/astGUIclient call logging
exten => h,1,DeadAGI(agi://127.0.0.1:4577/call_log--HVcauses ... EBUG-----${HANGUPCAUSE}-----${DIALSTATUS}-----${DIALEDTIME}-----${ANSWEREDTIME})
; Example phone extensions
; Extension 2000 Sipura/Linksys ATA line 1
exten => 2000,1,Dial(sip/spa2000,30,to) ; Ring, 30 secs max
exten => 2000,2,Voicemail,u2000 ; Send to voicemail...
; Extension 2001 Sipura/Linksys ATA line 2
exten => 2001,1,Dial(sip/spa2001,30,to) ; Ring, 30 secs max
exten => 2001,2,Voicemail,u2001 ; Send to voicemail...
; Extension 2102 rings Grandstream phone
exten => 2102,1,Dial(sip/gs102,30,to) ; Ring, 30 secs max
exten => 2102,2,Voicemail,u2102 ; Send to voicemail...
; Extension 401 rings the firefly softphone
exten => 401,1,Dial((IAX2/firefly01@firefly01/s||t)
exten => 401,2,Hangup
; 100-350 phone extensions now auto-generated
; extensions for other SIP and IAX call center phones
; cc100-cc150 SIP Phones
;exten => _1[0-5]X,1,Dial(sip/cc${EXTEN},20,to)
; cc300-cc350 IAX Phones
;exten => _3[0-5]X,1,Dial(IAX2/cc${EXTEN},20,to)
; extensions if using a T1 channelbank
;exten => _19XX,1,Dial(Zap/${EXTEN:2},30,o)
;exten => _19XX,2,Hangup
; Extension 4001 rings Zap phone (this example for FXS on Zap port 1)
;exten => 4001,1,Dial(Zap/1,30,o) ; ring Zap device 1
;exten => 4001,2,Voicemail,u4001 ; Send to voicemail...
; # timeout invalid rules
exten => #,1,Playback(invalid) ; "Thanks for trying the demo"
exten => #,2,Hangup ; Hang them up.
exten => t,1,Goto(#,1) ; If they take too long, give up
exten => i,1,Playback(invalid) ; "That's not valid, try again"
; Extensions for performance testing
;exten => _91999NXXXXXX,1,AGI(agi://127.0.0.1:4577/call_log)
;exten => _91999NXXXXXX,2,Dial(${TRUNKloop}/${EXTEN:2},,tTo)
;exten => _91999NXXXXXX,3,Hangup
exten => 999999999999,1,AGI(agi://127.0.0.1:4577/call_log)
exten => 999999999999,2,Dial(${TRUNKloop}/${EXTEN:1},,tTo)
exten => 999999999999,3,Hangup
; This is a loopback dialaround to allow for hearing of ringing for 3way calls
exten => _881NXXNXXXXXX,1,Answer
exten => _881NXXNXXXXXX,2,Dial(${TRUNKloop}/9${EXTEN:2},,To)
exten => _881NXXNXXXXXX,3,Hangup
; Vtiger fax and email log extensions
exten => _9118XXXXXXXX,1,Dial(${TRUNKblind}/9998818112,55,to)
exten => _9119XXXXXXXX,1,Dial(${TRUNKblind}/9998819112,55,to)
; CARRIER DIALING EXTENSIONS, USE THE ADMIN INTERFACE TO PROGRAM THESE
; dial an 800 outbound number
;exten => _91800NXXXXXX,1,AGI(agi://127.0.0.1:4577/call_log)
;exten => _91800NXXXXXX,2,Dial(${TRUNK}/${EXTEN:1},,To)
;exten => _91800NXXXXXX,3,Hangup
;exten => _91888NXXXXXX,1,AGI(agi://127.0.0.1:4577/call_log)
;exten => _91888NXXXXXX,2,Dial(${TRUNK}/${EXTEN:1},,To)
;exten => _91888NXXXXXX,3,Hangup
;exten => _91877NXXXXXX,1,AGI(agi://127.0.0.1:4577/call_log)
;exten => _91877NXXXXXX,2,Dial(${TRUNK}/${EXTEN:1},,To)
;exten => _91877NXXXXXX,3,Hangup
;exten => _91866NXXXXXX,1,AGI(agi://127.0.0.1:4577/call_log)
;exten => _91866NXXXXXX,2,Dial(${TRUNK}/${EXTEN:1},,To)
;exten => _91866NXXXXXX,3,Hangup
; dial a long distance outbound number
; This 'o' Dial flag is VERY important for VICIDIAL on outbound calls
;exten => _91NXXNXXXXXX,1,AGI(agi://127.0.0.1:4577/call_log)
;exten => _91NXXNXXXXXX,2,Dial(${TRUNKX}/${EXTEN:1},,To)
;exten => _91NXXNXXXXXX,3,Hangup
; dial a local outbound number (modified because of only LD T1)
;exten => _9NXXXXXX,1,AGI(agi://127.0.0.1:4577/call_log)
;exten => _9NXXXXXX,2,Dial(${TRUNK}/1727${EXTEN:1},,To)
;exten => _9NXXXXXX,3,Hangup
; dial a local 727 outbound number with area code
;exten => _9727NXXXXXX,1,AGI(agi://127.0.0.1:4577/call_log)
;exten => _9727NXXXXXX,2,Dial(${TRUNK}/1${EXTEN:1},,To)
;exten => _9727NXXXXXX,3,Hangup
; dial a long distance outbound number to the UK
; This 'o' Dial flag is VERY important for VICIDIAL on outbound calls,
;exten => _901144XXXXXXXXXX,1,AGI(agi://127.0.0.1:4577/call_log)
;exten => _901144XXXXXXXXXX,2,Dial(${TRUNKX}/${EXTEN:1},55,To)
;exten => _901144XXXXXXXXXX,3,Hangup
; dial a long distance outbound number to Australia
; This 'o' Dial flag is VERY important for VICIDIAL on outbound calls,
;exten => _901161XXXXXXXXX,1,AGI(agi://127.0.0.1:4577/call_log)
;exten => _901161XXXXXXXXX,2,Dial(${TRUNKX}/${EXTEN:1},,To)
;exten => _901161XXXXXXXXX,3,Hangup
; dial a long distance outbound number through BINFONE
; exten => _91NXXNXXXXXX,1,AGI(agi://127.0.0.1:4577/call_log)
; exten => _91NXXNXXXXXX,2,Dial(${TRUNKIAX}/${EXTEN:1},55,To)
; exten => _91NXXNXXXXXX,3,Hangup
; dial a long distance outbound number through a SIP provider
; exten => _91NXXNXXXXXX,1,AGI(agi://127.0.0.1:4577/call_log)
; exten => _91NXXNXXXXXX,2,Dial(sip/${EXTEN:1}@SIPtrunk,55,o)
; exten => _91NXXNXXXXXX,3,Hangup
; special extensions for North America to catch invalid phone numbers
; exten => _91XXX[0-1]XXXXXX,1,AGI(agi://127.0.0.1:4577/call_log)
; exten => _91XXX[0-1]XXXXXX,n,Dial(${TRUNKloop}/8889990011112,,to)
; exten => _91XXX[0-1]XXXXXX,n,Hangup
; exten => _91[0-1]XXXXXXXXX,1,AGI(agi://127.0.0.1:4577/call_log)
; exten => _91[0-1]XXXXXXXXX,n,Dial(${TRUNKloop}/8889990011112,,to)
; exten => _91[0-1]XXXXXXXXX,n,Hangup
; exten => _91XXXXXX,1,AGI(agi://127.0.0.1:4577/call_log)
; exten => _91XXXXXX,n,Dial(${TRUNKloop}/8889990011112,,to)
; exten => _91XXXXXX,n,Hangup
; exten => _91XXXXXXX,1,AGI(agi://127.0.0.1:4577/call_log)
; exten => _91XXXXXXX,n,Dial(${TRUNKloop}/8889990011112,,to)
; exten => _91XXXXXXX,n,Hangup
; exten => _91XXXXXXXX,1,AGI(agi://127.0.0.1:4577/call_log)
; exten => _91XXXXXXXX,n,Dial(${TRUNKloop}/8889990011112,,to)
; exten => _91XXXXXXXX,n,Hangup
; exten => _91XXXXXXXXX,1,AGI(agi://127.0.0.1:4577/call_log)
; exten => _91XXXXXXXXX,n,Dial(${TRUNKloop}/8889990011112,,to)
; exten => _91XXXXXXXXX,n,Hangup
; exten => _91XXXXXXXXXXX,1,AGI(agi://127.0.0.1:4577/call_log)
; exten => _91XXXXXXXXXXX,n,Dial(${TRUNKloop}/8889990011112,,to)
; exten => _91XXXXXXXXXXX,n,Hangup
; exten => _91XXXXXXXXXXXX,1,AGI(agi://127.0.0.1:4577/call_log)
; exten => _91XXXXXXXXXXXX,n,Dial(${TRUNKloop}/8889990011112,,to)
; exten => _91XXXXXXXXXXXX,n,Hangup
; exten => _91XXXXXXXXXXXXX,1,AGI(agi://127.0.0.1:4577/call_log)
; exten => _91XXXXXXXXXXXXX,n,Dial(${TRUNKloop}/8889990011112,,to)
; exten => _91XXXXXXXXXXXXX,n,Hangup
; dial a USA long distance outbound number through the loopback-no-log context
; exten => _91NXXNXXXXXX,1,AGI(agi://127.0.0.1:4577/call_log)
; exten => _91NXXNXXXXXX,2,Dial(${TRUNKloop}/888${EXTEN:2},55,o)
; exten => _91NXXNXXXXXX,3,Hangup
;exten => 888NXXNXXXXXX,1,Goto(loopback-no-log,91${EXTEN:3},1)
exten => 8889990011112,1,Goto(loopback-no-log,9990011112,1)
; Inbound call from BINFONE
; exten => 1112223333,1,AGI(agi://127.0.0.1:4577/call_log)
; exten => 1112223333,2,Dial(sip/gs102,55,o)
; exten => 1112223333,3,Hangup
; Extension 7275551212 - Inbound local number from PRI with 10 digit delivery
;exten => 7275551212,1,Ringing
;exten => 7275551212,2,Wait(1)
;exten => 7275551212,3,AGI(agi://127.0.0.1:4577/call_log--fullCID--${EXTEN}-----${CALLERID(all)}-----${CALLERID(num)}-----${CALLERID(name)})
;exten => 7275551212,4,Answer
;exten => 7275551212,5,Dial(sip/spa2000&sip/spa2001,30,To)
;exten => 7275551212,6,Voicemail,u2000
; parameters for call_inbound.agi (7 fields separated by five dashes "-----"):
; 1. the extension of the phone to ring as defined in the asterisk.phones table
; 2. the phone number that was called, for the live_inbound/_log entry
; 3. a text description of the number that was called in
; 4-7. optional fields, they are also passed as fields in the GUI to web browser
; This is not part of VICIDIAL, it is for astGUIclient agent use only
; Extension 3429 - Inbound 800 number (1-800-555-3429) example of RBS T1
; with 10 digit ANI and 4 digit DNIS star separated
;exten => _**3429,1,Ringing
;exten => _**3429,2,AGI(agi://127.0.0.1:4577/call_log)
;exten => _**3429,3,AGI(call_inbound.agi,spa2000-----8005553429-----Inbound 800-----x-----y-----z-----w)
;exten => _**3429,4,Answer
;exten => _**3429,5,Dial(sip/spa2000&sip/spa2001,30,to)
;exten => _**3429,6,Voicemail,u2000
; Extension 3429 - with ANI [callerID]
;exten => _*NXXNXXXXXX*3429,1,Ringing
;exten => _*NXXNXXXXXX*3429,2,AGI(agi://127.0.0.1:4577/call_log)
;exten => _*NXXNXXXXXX*3429,3,AGI(call_inbound.agi,spa2000-----8005553429-----Inbound 800-----x-----y-----z-----w)
;exten => _*NXXNXXXXXX*3429,4,Answer
;exten => _*NXXNXXXXXX*3429,5,Dial(sip/spa2000&sip/spa2001,30,to)
;exten => _*NXXNXXXXXX*3429,6,Voicemail,u2000
; parameters for agi-VDAD_ALL_inbound.agi (upto 12 fields separated by five dashes "-----"):
; Below are the parameters needed for the script to be run properly
; 1. the method of call handling for the script:
; - CID - CID received, add record with phone number
; - CIDLOOKUP - Lookup CID to find record in whole system
; - CIDLOOKUPRL - Restrict lookup to one list
; - CIDLOOKUPRC - Restrict lookup to one campaign's lists
; - CLOSER - Closer calls from VICIDIAL fronters
; - ANI - ANI received, add record with phone number (based on RBS T1s)
; - ANILOOKUP - Lookup ANI to find record in whole system
; - ANILOOKUPRL - Restrict lookup to one list
; - ANILOOKUPRC - Restrict lookup to one campaign's lists
; - VID - Add record with Vendor Lead Code received as argument 12
; - VIDLOOKUP - Lookup Vendor Lead Code received as argument 12 to find record in whole system
; - VIDLOOKUPRL - Restrict lookup to one list (argument 12)
; - VIDLOOKUPRC - Restrict lookup to one campaign's lists (argument 12)
; - VIDPROMPT - Prompt Vendor Lead Code to User with IVR to add record with Vendor Lead Code
; - VIDPROMPTLOOKUP - Prompt Vendor Lead Code to User with IVR to find record in whole system
; - VIDPROMPTLOOKUPRL - Restrict lookup to one list
; - VIDPROMPTLOOKUPRC - Restrict lookup to one campaign's lists
; - 3DIGITID - Enter 3 digit code to go to agent
; - 4DIGITID - Enter 4 digit code to go to agent
; - XDIGITID - Enter X digit code to go to agent(variable, i.e. 9DIGITID, 12DIGITID, etc...)
; 2. the method of searching for an available agent:
; - LO - Load Balance Overflow only (priority to home server)
; - LB - <default> Load Balance total system
; - SO - Home server only
; 3. the full name of the IN GROUP to be used in vicidial for the inbound call
; 4. the phone number that was called, for the log entry
; 5. the callerID or lead_id of the person that called(usually overridden)
; 6. the park extension audio file name if used
; 7. the status of the call initially(usually not used)
; 8. the list_id to insert the new lead under if it is new (and CID/ANI available)
; 9. the phone dialing code to insert with the new lead if new (and CID/ANI available)
; 10. the campaign_id to search within lists if CIDLOOKUPRC
; 11. the user to queue the call to for AGENTDIRECT in-group calls
; 12. vendor_lead_code if external mechanism like custom IVR is used to prompt user for ID
;
; inbound VICIDIAL call with CID delivery through T1 PRI
;exten => 1234,1,Answer ; Answer the line
;exten => 1234,2,AGI(agi-VDAD_ALL_inbound.agi,CID-----LB-----CL_GALLERIA-----7274515134-----Closer-----park----------999-----1)
;exten => 1234,3,Hangup
; inbound VICIDIAL transfer calls [can arrive through PRI T1 crossover, IAX or SIP channel]
exten => _90009.,1,Answer ; Answer the line
exten => _90009.,2,Dial(${TRUNKloop}/9${EXTEN},,to)
exten => _90009.,3,Hangup
exten => _990009.,1,Answer ; Answer the line, Sometimes needs to be removed
exten => _990009.,2,AGI(agi-VDAD_ALL_inbound.agi,CLOSER-----LB-----CL_TESTCAMP-----7275551212-----Closer-----park----------999-----1)
exten => _990009.,3,Hangup
; DID forwarded calls
exten => _99909*.,1,Answer
exten => _99909*.,2,AGI(agi-VDAD_ALL_inbound.agi)
exten => _99909*.,3,Hangup
; barge monitoring extension
exten => 8159,1,ZapBarge
exten => 8159,2,Hangup
; ZapBarge direct channel extensions
exten => _86120XX,1,ZapBarge(${EXTEN:5})
exten => _X48600XXX,1,MeetMeAdmin(${EXTEN:2},T,${EXTEN:0:1})
exten => _X48600XXX,2,Hangup
exten => _X38600XXX,1,MeetMeAdmin(${EXTEN:2},t,${EXTEN:0:1})
exten => _X38600XXX,2,Hangup
exten => _X28600XXX,1,MeetMeAdmin(${EXTEN:2},m,${EXTEN:0:1})
exten => _X28600XXX,2,Hangup
exten => _X18600XXX,1,MeetMeAdmin(${EXTEN:2},M,${EXTEN:0:1})
exten => _X18600XXX,2,Hangup
exten => _55558600XXX,1,MeetMeAdmin(${EXTEN:4},K)
exten => _55558600XXX,2,Hangup
exten => 8300,1,Hangup
; astGUIclient conferences
exten => _86000[0-4]X,1,Meetme,${EXTEN}|q
; VICIDIAL conferences
exten => _86000[5-9]X,1,Meetme,${EXTEN}|F
exten => _8600[1-2]XX,1,Meetme,${EXTEN}|F
; quiet entry and leaving conferences for VICIDIAL (inbound announce and SendDTMF)
exten => _78600XXX,1,Meetme,${EXTEN:1}|Fq
; quiet monitor-only extensions for meetme rooms (for room managers)
exten => _68600XXX,1,Meetme,${EXTEN:1}|Fmq
; quiet monitor-only entry and leaving conferences for VICIDIAL (recording)
exten => _58600XXX,1,Meetme,${EXTEN:1}|Fmq
; voicelab exten
exten => _86009XX,1,Meetme,${EXTEN}|Fmq
; voicelab exten moderator
exten => _986009XX,1,Meetme,${EXTEN:1}
; park channel for client GUI parking, hangup after 30 minutes
; create a GSM formatted audio file named "park.gsm" that is 30 minutes long
; and put it in /var/lib/asterisk/sounds
exten => 8301,1,Answer
exten => 8301,2,AGI(park_CID.agi)
exten => 8301,3,Playback(park)
exten => 8301,4,Hangup
exten => 8303,1,Answer
exten => 8303,2,AGI(park_CID.agi)
exten => 8303,3,Playback(conf)
exten => 8303,4,Hangup
; park channel for client GUI conferencing, hangup after 30 minutes
; create a GSM formatted audio file named "conf.gsm" that is 30 minutes long
; and put it in /var/lib/asterisk/sounds
exten => 8302,1,Answer
exten => 8302,2,Playback(conf)
exten => 8302,3,Hangup
exten => 8304,1,Answer
exten => 8304,2,Playback(ding)
exten => 8304,3,Hangup
; default audio for safe harbor 2-second-after-hello message then hangup
; create a GSM formatted audio file complies with safe harbor rules
; and put it in /var/lib/asterisk/sounds then change filename below
exten => 8307,1,Answer
exten => 8307,2,Playback(vm-goodbye)
exten => 8307,3,Hangup
; this is used for playing a message to an answering machine forwarded from AMD in VICIDIAL
exten => 8320,1,AGI(VD_amd.agi,${EXTEN}-----YES)
exten => 8320,2,Hangup
exten => _8320*.,1,AGI(VD_amd.agi,${EXTEN}-----YES)
exten => _8320*.,2,Hangup
; use for selective CallerID hangup by area code(hard-coded)
exten => 8352,1,AGI(agi-VDADselective_CID_hangup.agi,${EXTEN})
exten => 8352,2,Playback(safe_harbor)
exten => 8352,3,Hangup
; this is used for sending DTMF signals within conference calls, the client app
; sends the digits to be played in the callerID field
; sound files must be placed in /var/lib/asterisk/sounds
exten => 8500998,1,Answer
exten => 8500998,2,Playback(silence)
exten => 8500998,3,AGI(agi-dtmf.agi)
exten => 8500998,4,Hangup
; multi-remote-monitor entry extensions
exten => 8162,1,Dial(${TRUNKblind}/34567890123456789,55,to)
exten => 34567890123456789,1,Answer
exten => 34567890123456789,2,Goto(monitor,s,1)
;#### VDAD STANDARD TRANSFER ENTRIES ####
; Below are the parameters needed for the agi-VDAD_ALL_outbound.agi script to be run properly
; 1. the method of call handling for the script:
; - NORMAL - <default> Standard outbound routing to agent
; - TEST - For performance testing only
; - BROADCAST - For no-agent broadcast dialing
; - SURVEY - For survery question then on to agent
; - REMINDER - Reminder campaign
; - REMINDX - Reminder with transfer to agent
; 2. the method of searching for an available agent:
; - LB - <default> Load Balance total system
; - LO - Load Balance Overflow only (priority to home server)
; - SO - Home server only
; 3. the sound file to play when doing a SURVEY, REMINDER, REMINDX campaign
; 4. the acceptible dtmf digits for a SURVEY
; 5. the out-opt digit for a SURVEY (must be in the digit map)
; 6. the sound file to play for a SURVEY when transfering to an agent
; 7. the sound file to play for a SURVEY when DNCing the call
; 8. OPTIN or OPTOUT: if OPTIN call is only sent to agent with button press
; if OPTOUT call is sent to agent if no button press at all
; 9. the status that is use for a SURVEY when someone opts out
; if the status is DNC it will also add them to the internal dnc table
; VICIDIAL_auto_dialer transfer script for no-agent campaigns:
exten => 8364,1,Playback(sip-silence)
exten => 8364,2,AGI(agi://127.0.0.1:4577/call_log)
exten => 8364,3,AGI(agi-VDAD_ALL_outbound.agi,NORMAL-----LB)
exten => 8364,4,AGI(agi-VDAD_ALL_outbound.agi,NORMAL-----LB)
exten => 8364,5,Hangup
; VICIDIAL_auto_dialer transfer script:
exten => 8365,1,Playback(sip-silence)
exten => 8365,2,AGI(agi://127.0.0.1:4577/call_log)
exten => 8365,3,AGI(agi-VDAD_ALL_outbound.agi,NORMAL-----SO)
exten => 8365,4,AGI(agi-VDAD_ALL_outbound.agi,NORMAL-----SO)
exten => 8365,5,Hangup
; VICIDIAL_auto_dialer transfer script SURVEY at beginning:
exten => 8366,1,Playback(sip-silence)
exten => 8366,2,AGI(agi://127.0.0.1:4577/call_log)
exten => 8366,3,AGI(agi-VDAD_ALL_outbound.agi,SURVEYCAMP-----LB)
exten => 8366,4,AGI(agi-VDAD_ALL_outbound.agi,SURVEYCAMP-----LB)
exten => 8366,5,Hangup
; VICIDIAL_auto_dialer transfer script Load Balance Overflow:
exten => 8367,1,Playback(sip-silence)
exten => 8367,2,AGI(agi://127.0.0.1:4577/call_log)
exten => 8367,3,AGI(agi-VDAD_ALL_outbound.agi,NORMAL-----LO)
exten => 8367,4,AGI(agi-VDAD_ALL_outbound.agi,NORMAL-----LO)
exten => 8367,5,Hangup
; VICIDIAL_auto_dialer transfer script Load Balanced:
exten => 8368,1,Playback(sip-silence)
exten => 8368,2,AGI(agi://127.0.0.1:4577/call_log)
exten => 8368,3,AGI(agi-VDAD_ALL_outbound.agi,NORMAL-----LB)
exten => 8368,4,AGI(agi-VDAD_ALL_outbound.agi,NORMAL-----LB)
exten => 8368,5,Hangup
; VICIDIAL_auto_dialer transfer script AMD with Load Balanced:
exten => 8369,1,Playback(sip-silence)
exten => 8369,2,AGI(agi://127.0.0.1:4577/call_log)
exten => 8369,3,AMD(2000|2000|1000|5000|120|50|4|256)
exten => 8369,4,AGI(VD_amd.agi,${EXTEN})
exten => 8369,5,AGI(agi-VDAD_ALL_outbound.agi,NORMAL-----LB)
exten => 8369,6,AGI(agi-VDAD_ALL_outbound.agi,NORMAL-----LB)
exten => 8369,7,Hangup
; VICIDIAL auto-dial reminder script
exten => 8372,1,Playback(sip-silence)
exten => 8372,2,AGI(agi://127.0.0.1:4577/call_log)
exten => 8372,3,AGI(agi-VDADautoREMINDER.agi,${EXTEN})
exten => 8372,4,AGI(agi-VDADautoREMINDER.agi,${EXTEN})
exten => 8372,5,Hangup
; VICIDIAL SURVEY transfer script AMD with Load Balanced:
exten => 8373,1,Playback(sip-silence)
exten => 8373,2,AGI(agi://127.0.0.1:4577/call_log)
exten => 8373,3,AMD(2000|2000|1000|5000|120|50|4|256)
exten => 8373,4,AGI(VD_amd.agi,${EXTEN})
exten => 8373,5,AGI(agi-VDAD_ALL_outbound.agi,SURVEYCAMP-----LB)
exten => 8373,6,AGI(agi-VDAD_ALL_outbound.agi,SURVEYCAMP-----LB)
exten => 8373,7,Hangup
; VICIDIAL SURVEY transfer script with Cepstral names:
exten => 8374,1,Playback(sip-silence)
exten => 8374,2,AGI(agi://127.0.0.1:4577/call_log)
exten => 8374,3,AGI(agi-VDAD_ALL_outbound.agi,SURVEYCAMPCEP-----LB)
exten => 8374,4,AGI(agi-VDAD_ALL_outbound.agi,SURVEYCAMPCEP-----LB)
exten => 8374,5,Hangup
; VICIDIAL SURVEY transfer script AMD with Cepstral variables:
exten => 8375,1,Playback(sip-silence)
exten => 8375,2,AGI(agi://127.0.0.1:4577/call_log)
exten => 8375,3,AMD(2000|2000|1000|5000|120|50|4|256)
exten => 8375,4,AGI(VD_amd.agi,${EXTEN})
exten => 8375,5,AGI(agi-VDAD_ALL_outbound.agi,SURVEYCAMPCEP-----LB)
exten => 8375,6,AGI(agi-VDAD_ALL_outbound.agi,SURVEYCAMPCEP-----LB)
exten => 8375,7,Hangup
; PERFORMANCE TESTING
exten => _999XXXXXX1,1,Answer
exten => _999XXXXXX1,2,Wait(2)
exten => _999XXXXXX1,3,Playback(vicidial-welcome)
exten => _999XXXXXX1,4,Hangup
exten => _999XX11112,1,Wait(2)
exten => _999XX11112,2,Answer
exten => _999XX11112,3,Playback(ss-noservice)
exten => _999XX11112,4,Playback(vm-goodbye)
exten => _999XX11112,5,Hangup
exten => _999XX18112,1,Wait(2)
exten => _999XX18112,2,Answer
exten => _999XX18112,3,Playback(vtiger-fax)
exten => _999XX18112,4,Playback(vtiger-fax)
exten => _999XX18112,5,Hangup
exten => _999XX19112,1,Wait(2)
exten => _999XX19112,2,Answer
exten => _999XX19112,3,Playback(vtiger-email)
exten => _999XX19112,4,Playback(vtiger-email)
exten => _999XX19112,5,Hangup
exten => _999XXXX112,1,Wait(5)
exten => _999XXXX112,2,Answer
exten => _999XXXX112,3,Playback(demo-instruct)
exten => _999XXXX112,4,Playback(demo-instruct)
exten => _999XXXX112,5,Hangup
exten => _999XXXXXX2,1,Wait(8)
exten => _999XXXXXX2,2,Answer
exten => _999XXXXXX2,3,Playback(demo-instruct)
exten => _999XXXXXX2,4,Hangup
exten => _999XXXXXX3,1,Set(PRI_CAUSE=1)
exten => _999XXXXXX3,2,Hangup
exten => _999XXXXXX4,1,Set(PRI_CAUSE=27)
exten => _999XXXXXX4,2,Hangup
exten => _999XXXXXX5,1,Wait(60)
exten => _999XXXXXX5,2,Hangup
exten => _999XXXXXX6,1,Wait(10)
exten => _999XXXXXX6,2,Answer
exten => _999XXXXXX6,3,Playback(demo-instruct)
exten => _999XXXXXX6,4,Hangup
exten => _999XXXXXX7,1,Wait(12)
exten => _999XXXXXX7,2,Answer
exten => _999XXXXXX7,3,Playback(demo-enterkeywords)
exten => _999XXXXXX7,4,Hangup
exten => _999XXXXXX8,1,Set(PRI_CAUSE=17)
exten => _999XXXXXX8,2,Hangup
exten => _999XXXXXX9,1,Wait(6)
exten => _999XXXXXX9,2,Answer
exten => _999XXXXXX9,3,Playback(demo-abouttotry)
exten => _999XXXXXX9,4,Hangup
exten => _999XXXXXX0,1,Wait(5)
exten => _999XXXXXX0,2,Answer
exten => _999XXXXXX0,3,Playback(vm-goodbye)
exten => _999XXXXXX0,4,Hangup
exten => 99999999999,1,Answer
exten => 99999999999,2,Playback(conf)
exten => 99999999999,3,Playback(conf)
exten => 99999999999,4,Playback(conf)
exten => 99999999999,5,Playback(conf)
exten => 99999999999,6,Playback(conf)
exten => 99999999999,7,Playback(conf)
exten => 99999999999,8,Playback(conf)
exten => 99999999999,9,Playback(conf)
exten => 99999999999,10,Playback(conf)
exten => 99999999999,11,Playback(conf)
exten => 99999999999,12,Playback(conf)
exten => 99999999999,13,Playback(conf)
exten => 99999999999,14,Hangup
[monitor]
exten => h,1,DeadAGI(agi://127.0.0.1:4577/call_log--HVcauses ... EBUG-----${HANGUPCAUSE}-----${DIALSTATUS}-----${DIALEDTIME}-----${ANSWEREDTIME})
exten => s,1,Set(TIMEOUT(digit)=10)
exten => s,n,Set(TIMEOUT(response)=10)
exten => s,n,Set(MEETME_EXIT_CONTEXT=monitor_exit)
exten => s,n,Background(vm-extension) ; need audio prompt.
exten => s,n,WaitExten(10)
exten => i,1,Goto(monitor_exit,s,1)
exten => #,1,Goto(monitor_exit,s,1)
exten => t,1,Goto(monitor_exit,s,1)
exten => _8[0-2]XX,1,Meetme(8600${EXTEN:1},mqX) ; Listen
exten => _99[0-2]XX,1,Meetme(8600${EXTEN:2},X) ; Barge
[monitor_exit]
exten => h,1,DeadAGI(agi://127.0.0.1:4577/call_log--HVcauses ... EBUG-----${HANGUPCAUSE}-----${DIALSTATUS}-----${DIALEDTIME}-----${ANSWEREDTIME})
exten => _X,1,Goto(monitor,s,1)
exten => i,1,Goto(monitor,s,1)
exten => #,1,Goto(monitor,s,1)
exten => t,1,Goto(monitor,s,1)
BUILD: 100510-2015
Asterisk 1.4.38-vici
Dahdi -2.2.4 complete version
kernel 2.6.18-128.el5PAE
RHEL v 5.3 (32 bit)
Sangoma cards = 2 (A104d QUAD T1/E1 AFT card each), No extra software
PRI's = 8
Campaign Settings:
auto dial level= 10
hopper level= 500
dial time out= 60
Max VICIDIAL Trunks= 240
Max Calls per Second= 4/sec
Remote agent Lines : 24
Leads file has 5000 leads
We did two Auto dial Outbound survey campaign with the above configuration. In the first test, we used the following extensions.conf
[general]
static=yes
writeprotect=no
[default]
exten=>_91XXXXXXXXXX,1,Dial(DAHDI/g1/0${EXTEN:2},30|o)
exten=>_91XXXXXXXXXX,n,Hangup()
; VICIDIAL_auto_dialer transfer script SURVEY at beginning:
;exten => 8366,1,AGI(agi://127.0.0.1:4577/call_log)
exten => 8366,n,Playback(welcome_tofrenzo_the_best_way_english)
exten => 8366,n,Hangup
;exten => h,1,DeadAGI(agi://127.0.0.1:4577/call_log--HVcauses ... EBUG-----${HANGUPCAUSE}-----${DIALSTATUS}-----${DIALEDTIME}-----${ANSWEREDTIME})
If you would notice, we had removed most of the exten provided by vicidial and the prompt playback was defined in the extensions.conf. We were able to complete the campaign in around 30 minutes with no perceptible delay in prompt playback when users answered the call.
We ran the same auto dial outbound survey campaign with the same campaign setting as above, but using extensions.conf which you get on installing vicidial (extensions.conf is given at the bottom)
However, we got perceptible delay in prompt playback ranging from 5 to 12 seconds when users answered the call.
On monitoring the master.csv for this test run showed delay on those numbers where the delay was noticed. For instance, you can see below that the call got transfered from local channel to dahdi channel in 5 seconds, which was also the delay in prompt playback on answering the call by this user
"","0000000000","919651363002","default","""V0120124232000000220"" <0000000000>","Local/919651363002@default-8196,2","DAHDI/29-1","Dial","DAHDI/g1/09651363002|30|o","2011-01-20 07:13:12","2011-01-20 07:13:41","2011-01-20 07:13:46",34,5,"ANSWERED","DOCUMENTATION","1295507592.633",""
We did not see any such delay in master.csv when we ran the first test. What could be going wrong here. Do you think the following extra entries under "VICIDIAL_auto_dialer transfer script SURVEY at beginning" causing this delay. If not, then what are they doing, I never used them in the first test and got good result. This is just a conjecture and curious to know what is going wrong.
exten => 8366,2,AGI(agi://127.0.0.1:4577/call_log)
exten => 8366,3,AGI(agi-VDAD_ALL_outbound.agi,SURVEYCAMP-----LB)
exten => 8366,4,AGI(agi-VDAD_ALL_outbound.agi,SURVEYCAMP-----LB)
extensions.conf for second test
[general]
static=yes
writeprotect=no
[globals]
CONSOLE=Console/dsp ; Console interface for demo
TRUNK=Zap/r1 ; Trunk interface
TRUNKX=Zap/r2 ; 2nd trunk interface
TRUNKIAX=IAX2/ASTtest1:test@10.10.10.16:4569 ; IAX trunk interface
TRUNKIAX1=IAX2/ASTtest1:test@10.10.10.16:4569 ; IAX trunk interface
TRUNKBINFONE=IAX2/1112223333:PASSWORD@iax.binfone.com ; IAX trunk interface
SIPtrunk=SIP/1234:PASSWORD@sip.provider.net ; SIP trunk
#include extensions-vicidial.conf
[trunkinbound]
; DID call routing process
exten => _X.,1,AGI(agi-DID_route.agi)
; FastAGI for VICIDIAL/astGUIclient call logging
exten => h,1,DeadAGI(agi://127.0.0.1:4577/call_log--HVcauses ... EBUG-----${HANGUPCAUSE}-----${DIALSTATUS}-----${DIALEDTIME}-----${ANSWEREDTIME})
[loopback-no-log]
; This context is to accept calls that have already been logged in another context in Vicidial
; and has been sent through one of the loopbacks. This is why this context is missing the h extension.
; Do not put any extensions in this context unless you specifically understand what this means.
;exten => _91NXXNXXXXXX,1,Dial(${TRUNKX}/${EXTEN:1},,To)
;exten => _91NXXNXXXXXX,n,Hangup
; special Canadian PRI callerIDname settings FOR USE IN LOOPBACK CONTEXT ONLY
;exten => _91NXXNXXXXXX,1,Set(CALLERID(name)="ACME Widgets")
;exten => _91NXXNXXXXXX,n,AGI(agi-CANADA_PRI_CIDname.agi)
;exten => _91NXXNXXXXXX,n,Dial(${TRUNKX}/${EXTEN:1},,To)
;exten => _91NXXNXXXXXX,n,Hangup
exten => _999XX11112,1,Wait(2)
exten => _999XX11112,n,Answer
exten => _999XX11112,n,Playback(ss-noservice)
exten => _999XX11112,n,Playback(vm-goodbye)
exten => _999XX11112,n,Hangup
[default]
include => vicidial-auto
exten=>_91XXXXXXXXXX,1,AGI(agi://127.0.0.1:4577/call_log)
exten=>_91XXXXXXXXXX,n,Dial(DAHDI/g1/0${EXTEN:2},30|o)
exten=>_91XXXXXXXXXX,n,Hangup()
; VICI-GROUP DIRECT SUPPORT LINE (VICIHELP[84244357])
exten => _84244XXX,1,Dial(IAX2/vicihelp/${EXTEN:5})
; Local agent alert extensions
exten => _8600XXX*.,1,AGI(agi-VDADfixCXFER.agi)
exten => _78600XXX*.,1,AGI(agi-VDADfixCXFER.agi)
; Local blind monitoring
exten => _08600XXX,1,Dial(${TRUNKblind}/6${EXTEN:1},55,To)
; playback of recorded prompts
exten => _851XXXXX,1,Answer
exten => _851XXXXX,2,Playback(${EXTEN})
exten => _851XXXXX,3,Hangup
; this is used for playing a message to an answering machine forwarded from AMD in VICIDIAL
exten => _7851XXXXX,1,WaitForSilence(2000,2) ; AMD got machine. leave message after recording
exten => _7851XXXXX,2,Playback(${EXTEN:1})
exten => _7851XXXXX,3,AGI(VD_amd_post.agi,${EXTEN:1})
exten => _7851XXXXX,4,Hangup
; FastAGI for VICIDIAL/astGUIclient call logging
exten => h,1,DeadAGI(agi://127.0.0.1:4577/call_log--HVcauses ... EBUG-----${HANGUPCAUSE}-----${DIALSTATUS}-----${DIALEDTIME}-----${ANSWEREDTIME})
; Example phone extensions
; Extension 2000 Sipura/Linksys ATA line 1
exten => 2000,1,Dial(sip/spa2000,30,to) ; Ring, 30 secs max
exten => 2000,2,Voicemail,u2000 ; Send to voicemail...
; Extension 2001 Sipura/Linksys ATA line 2
exten => 2001,1,Dial(sip/spa2001,30,to) ; Ring, 30 secs max
exten => 2001,2,Voicemail,u2001 ; Send to voicemail...
; Extension 2102 rings Grandstream phone
exten => 2102,1,Dial(sip/gs102,30,to) ; Ring, 30 secs max
exten => 2102,2,Voicemail,u2102 ; Send to voicemail...
; Extension 401 rings the firefly softphone
exten => 401,1,Dial((IAX2/firefly01@firefly01/s||t)
exten => 401,2,Hangup
; 100-350 phone extensions now auto-generated
; extensions for other SIP and IAX call center phones
; cc100-cc150 SIP Phones
;exten => _1[0-5]X,1,Dial(sip/cc${EXTEN},20,to)
; cc300-cc350 IAX Phones
;exten => _3[0-5]X,1,Dial(IAX2/cc${EXTEN},20,to)
; extensions if using a T1 channelbank
;exten => _19XX,1,Dial(Zap/${EXTEN:2},30,o)
;exten => _19XX,2,Hangup
; Extension 4001 rings Zap phone (this example for FXS on Zap port 1)
;exten => 4001,1,Dial(Zap/1,30,o) ; ring Zap device 1
;exten => 4001,2,Voicemail,u4001 ; Send to voicemail...
; # timeout invalid rules
exten => #,1,Playback(invalid) ; "Thanks for trying the demo"
exten => #,2,Hangup ; Hang them up.
exten => t,1,Goto(#,1) ; If they take too long, give up
exten => i,1,Playback(invalid) ; "That's not valid, try again"
; Extensions for performance testing
;exten => _91999NXXXXXX,1,AGI(agi://127.0.0.1:4577/call_log)
;exten => _91999NXXXXXX,2,Dial(${TRUNKloop}/${EXTEN:2},,tTo)
;exten => _91999NXXXXXX,3,Hangup
exten => 999999999999,1,AGI(agi://127.0.0.1:4577/call_log)
exten => 999999999999,2,Dial(${TRUNKloop}/${EXTEN:1},,tTo)
exten => 999999999999,3,Hangup
; This is a loopback dialaround to allow for hearing of ringing for 3way calls
exten => _881NXXNXXXXXX,1,Answer
exten => _881NXXNXXXXXX,2,Dial(${TRUNKloop}/9${EXTEN:2},,To)
exten => _881NXXNXXXXXX,3,Hangup
; Vtiger fax and email log extensions
exten => _9118XXXXXXXX,1,Dial(${TRUNKblind}/9998818112,55,to)
exten => _9119XXXXXXXX,1,Dial(${TRUNKblind}/9998819112,55,to)
; CARRIER DIALING EXTENSIONS, USE THE ADMIN INTERFACE TO PROGRAM THESE
; dial an 800 outbound number
;exten => _91800NXXXXXX,1,AGI(agi://127.0.0.1:4577/call_log)
;exten => _91800NXXXXXX,2,Dial(${TRUNK}/${EXTEN:1},,To)
;exten => _91800NXXXXXX,3,Hangup
;exten => _91888NXXXXXX,1,AGI(agi://127.0.0.1:4577/call_log)
;exten => _91888NXXXXXX,2,Dial(${TRUNK}/${EXTEN:1},,To)
;exten => _91888NXXXXXX,3,Hangup
;exten => _91877NXXXXXX,1,AGI(agi://127.0.0.1:4577/call_log)
;exten => _91877NXXXXXX,2,Dial(${TRUNK}/${EXTEN:1},,To)
;exten => _91877NXXXXXX,3,Hangup
;exten => _91866NXXXXXX,1,AGI(agi://127.0.0.1:4577/call_log)
;exten => _91866NXXXXXX,2,Dial(${TRUNK}/${EXTEN:1},,To)
;exten => _91866NXXXXXX,3,Hangup
; dial a long distance outbound number
; This 'o' Dial flag is VERY important for VICIDIAL on outbound calls
;exten => _91NXXNXXXXXX,1,AGI(agi://127.0.0.1:4577/call_log)
;exten => _91NXXNXXXXXX,2,Dial(${TRUNKX}/${EXTEN:1},,To)
;exten => _91NXXNXXXXXX,3,Hangup
; dial a local outbound number (modified because of only LD T1)
;exten => _9NXXXXXX,1,AGI(agi://127.0.0.1:4577/call_log)
;exten => _9NXXXXXX,2,Dial(${TRUNK}/1727${EXTEN:1},,To)
;exten => _9NXXXXXX,3,Hangup
; dial a local 727 outbound number with area code
;exten => _9727NXXXXXX,1,AGI(agi://127.0.0.1:4577/call_log)
;exten => _9727NXXXXXX,2,Dial(${TRUNK}/1${EXTEN:1},,To)
;exten => _9727NXXXXXX,3,Hangup
; dial a long distance outbound number to the UK
; This 'o' Dial flag is VERY important for VICIDIAL on outbound calls,
;exten => _901144XXXXXXXXXX,1,AGI(agi://127.0.0.1:4577/call_log)
;exten => _901144XXXXXXXXXX,2,Dial(${TRUNKX}/${EXTEN:1},55,To)
;exten => _901144XXXXXXXXXX,3,Hangup
; dial a long distance outbound number to Australia
; This 'o' Dial flag is VERY important for VICIDIAL on outbound calls,
;exten => _901161XXXXXXXXX,1,AGI(agi://127.0.0.1:4577/call_log)
;exten => _901161XXXXXXXXX,2,Dial(${TRUNKX}/${EXTEN:1},,To)
;exten => _901161XXXXXXXXX,3,Hangup
; dial a long distance outbound number through BINFONE
; exten => _91NXXNXXXXXX,1,AGI(agi://127.0.0.1:4577/call_log)
; exten => _91NXXNXXXXXX,2,Dial(${TRUNKIAX}/${EXTEN:1},55,To)
; exten => _91NXXNXXXXXX,3,Hangup
; dial a long distance outbound number through a SIP provider
; exten => _91NXXNXXXXXX,1,AGI(agi://127.0.0.1:4577/call_log)
; exten => _91NXXNXXXXXX,2,Dial(sip/${EXTEN:1}@SIPtrunk,55,o)
; exten => _91NXXNXXXXXX,3,Hangup
; special extensions for North America to catch invalid phone numbers
; exten => _91XXX[0-1]XXXXXX,1,AGI(agi://127.0.0.1:4577/call_log)
; exten => _91XXX[0-1]XXXXXX,n,Dial(${TRUNKloop}/8889990011112,,to)
; exten => _91XXX[0-1]XXXXXX,n,Hangup
; exten => _91[0-1]XXXXXXXXX,1,AGI(agi://127.0.0.1:4577/call_log)
; exten => _91[0-1]XXXXXXXXX,n,Dial(${TRUNKloop}/8889990011112,,to)
; exten => _91[0-1]XXXXXXXXX,n,Hangup
; exten => _91XXXXXX,1,AGI(agi://127.0.0.1:4577/call_log)
; exten => _91XXXXXX,n,Dial(${TRUNKloop}/8889990011112,,to)
; exten => _91XXXXXX,n,Hangup
; exten => _91XXXXXXX,1,AGI(agi://127.0.0.1:4577/call_log)
; exten => _91XXXXXXX,n,Dial(${TRUNKloop}/8889990011112,,to)
; exten => _91XXXXXXX,n,Hangup
; exten => _91XXXXXXXX,1,AGI(agi://127.0.0.1:4577/call_log)
; exten => _91XXXXXXXX,n,Dial(${TRUNKloop}/8889990011112,,to)
; exten => _91XXXXXXXX,n,Hangup
; exten => _91XXXXXXXXX,1,AGI(agi://127.0.0.1:4577/call_log)
; exten => _91XXXXXXXXX,n,Dial(${TRUNKloop}/8889990011112,,to)
; exten => _91XXXXXXXXX,n,Hangup
; exten => _91XXXXXXXXXXX,1,AGI(agi://127.0.0.1:4577/call_log)
; exten => _91XXXXXXXXXXX,n,Dial(${TRUNKloop}/8889990011112,,to)
; exten => _91XXXXXXXXXXX,n,Hangup
; exten => _91XXXXXXXXXXXX,1,AGI(agi://127.0.0.1:4577/call_log)
; exten => _91XXXXXXXXXXXX,n,Dial(${TRUNKloop}/8889990011112,,to)
; exten => _91XXXXXXXXXXXX,n,Hangup
; exten => _91XXXXXXXXXXXXX,1,AGI(agi://127.0.0.1:4577/call_log)
; exten => _91XXXXXXXXXXXXX,n,Dial(${TRUNKloop}/8889990011112,,to)
; exten => _91XXXXXXXXXXXXX,n,Hangup
; dial a USA long distance outbound number through the loopback-no-log context
; exten => _91NXXNXXXXXX,1,AGI(agi://127.0.0.1:4577/call_log)
; exten => _91NXXNXXXXXX,2,Dial(${TRUNKloop}/888${EXTEN:2},55,o)
; exten => _91NXXNXXXXXX,3,Hangup
;exten => 888NXXNXXXXXX,1,Goto(loopback-no-log,91${EXTEN:3},1)
exten => 8889990011112,1,Goto(loopback-no-log,9990011112,1)
; Inbound call from BINFONE
; exten => 1112223333,1,AGI(agi://127.0.0.1:4577/call_log)
; exten => 1112223333,2,Dial(sip/gs102,55,o)
; exten => 1112223333,3,Hangup
; Extension 7275551212 - Inbound local number from PRI with 10 digit delivery
;exten => 7275551212,1,Ringing
;exten => 7275551212,2,Wait(1)
;exten => 7275551212,3,AGI(agi://127.0.0.1:4577/call_log--fullCID--${EXTEN}-----${CALLERID(all)}-----${CALLERID(num)}-----${CALLERID(name)})
;exten => 7275551212,4,Answer
;exten => 7275551212,5,Dial(sip/spa2000&sip/spa2001,30,To)
;exten => 7275551212,6,Voicemail,u2000
; parameters for call_inbound.agi (7 fields separated by five dashes "-----"):
; 1. the extension of the phone to ring as defined in the asterisk.phones table
; 2. the phone number that was called, for the live_inbound/_log entry
; 3. a text description of the number that was called in
; 4-7. optional fields, they are also passed as fields in the GUI to web browser
; This is not part of VICIDIAL, it is for astGUIclient agent use only
; Extension 3429 - Inbound 800 number (1-800-555-3429) example of RBS T1
; with 10 digit ANI and 4 digit DNIS star separated
;exten => _**3429,1,Ringing
;exten => _**3429,2,AGI(agi://127.0.0.1:4577/call_log)
;exten => _**3429,3,AGI(call_inbound.agi,spa2000-----8005553429-----Inbound 800-----x-----y-----z-----w)
;exten => _**3429,4,Answer
;exten => _**3429,5,Dial(sip/spa2000&sip/spa2001,30,to)
;exten => _**3429,6,Voicemail,u2000
; Extension 3429 - with ANI [callerID]
;exten => _*NXXNXXXXXX*3429,1,Ringing
;exten => _*NXXNXXXXXX*3429,2,AGI(agi://127.0.0.1:4577/call_log)
;exten => _*NXXNXXXXXX*3429,3,AGI(call_inbound.agi,spa2000-----8005553429-----Inbound 800-----x-----y-----z-----w)
;exten => _*NXXNXXXXXX*3429,4,Answer
;exten => _*NXXNXXXXXX*3429,5,Dial(sip/spa2000&sip/spa2001,30,to)
;exten => _*NXXNXXXXXX*3429,6,Voicemail,u2000
; parameters for agi-VDAD_ALL_inbound.agi (upto 12 fields separated by five dashes "-----"):
; Below are the parameters needed for the script to be run properly
; 1. the method of call handling for the script:
; - CID - CID received, add record with phone number
; - CIDLOOKUP - Lookup CID to find record in whole system
; - CIDLOOKUPRL - Restrict lookup to one list
; - CIDLOOKUPRC - Restrict lookup to one campaign's lists
; - CLOSER - Closer calls from VICIDIAL fronters
; - ANI - ANI received, add record with phone number (based on RBS T1s)
; - ANILOOKUP - Lookup ANI to find record in whole system
; - ANILOOKUPRL - Restrict lookup to one list
; - ANILOOKUPRC - Restrict lookup to one campaign's lists
; - VID - Add record with Vendor Lead Code received as argument 12
; - VIDLOOKUP - Lookup Vendor Lead Code received as argument 12 to find record in whole system
; - VIDLOOKUPRL - Restrict lookup to one list (argument 12)
; - VIDLOOKUPRC - Restrict lookup to one campaign's lists (argument 12)
; - VIDPROMPT - Prompt Vendor Lead Code to User with IVR to add record with Vendor Lead Code
; - VIDPROMPTLOOKUP - Prompt Vendor Lead Code to User with IVR to find record in whole system
; - VIDPROMPTLOOKUPRL - Restrict lookup to one list
; - VIDPROMPTLOOKUPRC - Restrict lookup to one campaign's lists
; - 3DIGITID - Enter 3 digit code to go to agent
; - 4DIGITID - Enter 4 digit code to go to agent
; - XDIGITID - Enter X digit code to go to agent(variable, i.e. 9DIGITID, 12DIGITID, etc...)
; 2. the method of searching for an available agent:
; - LO - Load Balance Overflow only (priority to home server)
; - LB - <default> Load Balance total system
; - SO - Home server only
; 3. the full name of the IN GROUP to be used in vicidial for the inbound call
; 4. the phone number that was called, for the log entry
; 5. the callerID or lead_id of the person that called(usually overridden)
; 6. the park extension audio file name if used
; 7. the status of the call initially(usually not used)
; 8. the list_id to insert the new lead under if it is new (and CID/ANI available)
; 9. the phone dialing code to insert with the new lead if new (and CID/ANI available)
; 10. the campaign_id to search within lists if CIDLOOKUPRC
; 11. the user to queue the call to for AGENTDIRECT in-group calls
; 12. vendor_lead_code if external mechanism like custom IVR is used to prompt user for ID
;
; inbound VICIDIAL call with CID delivery through T1 PRI
;exten => 1234,1,Answer ; Answer the line
;exten => 1234,2,AGI(agi-VDAD_ALL_inbound.agi,CID-----LB-----CL_GALLERIA-----7274515134-----Closer-----park----------999-----1)
;exten => 1234,3,Hangup
; inbound VICIDIAL transfer calls [can arrive through PRI T1 crossover, IAX or SIP channel]
exten => _90009.,1,Answer ; Answer the line
exten => _90009.,2,Dial(${TRUNKloop}/9${EXTEN},,to)
exten => _90009.,3,Hangup
exten => _990009.,1,Answer ; Answer the line, Sometimes needs to be removed
exten => _990009.,2,AGI(agi-VDAD_ALL_inbound.agi,CLOSER-----LB-----CL_TESTCAMP-----7275551212-----Closer-----park----------999-----1)
exten => _990009.,3,Hangup
; DID forwarded calls
exten => _99909*.,1,Answer
exten => _99909*.,2,AGI(agi-VDAD_ALL_inbound.agi)
exten => _99909*.,3,Hangup
; barge monitoring extension
exten => 8159,1,ZapBarge
exten => 8159,2,Hangup
; ZapBarge direct channel extensions
exten => _86120XX,1,ZapBarge(${EXTEN:5})
exten => _X48600XXX,1,MeetMeAdmin(${EXTEN:2},T,${EXTEN:0:1})
exten => _X48600XXX,2,Hangup
exten => _X38600XXX,1,MeetMeAdmin(${EXTEN:2},t,${EXTEN:0:1})
exten => _X38600XXX,2,Hangup
exten => _X28600XXX,1,MeetMeAdmin(${EXTEN:2},m,${EXTEN:0:1})
exten => _X28600XXX,2,Hangup
exten => _X18600XXX,1,MeetMeAdmin(${EXTEN:2},M,${EXTEN:0:1})
exten => _X18600XXX,2,Hangup
exten => _55558600XXX,1,MeetMeAdmin(${EXTEN:4},K)
exten => _55558600XXX,2,Hangup
exten => 8300,1,Hangup
; astGUIclient conferences
exten => _86000[0-4]X,1,Meetme,${EXTEN}|q
; VICIDIAL conferences
exten => _86000[5-9]X,1,Meetme,${EXTEN}|F
exten => _8600[1-2]XX,1,Meetme,${EXTEN}|F
; quiet entry and leaving conferences for VICIDIAL (inbound announce and SendDTMF)
exten => _78600XXX,1,Meetme,${EXTEN:1}|Fq
; quiet monitor-only extensions for meetme rooms (for room managers)
exten => _68600XXX,1,Meetme,${EXTEN:1}|Fmq
; quiet monitor-only entry and leaving conferences for VICIDIAL (recording)
exten => _58600XXX,1,Meetme,${EXTEN:1}|Fmq
; voicelab exten
exten => _86009XX,1,Meetme,${EXTEN}|Fmq
; voicelab exten moderator
exten => _986009XX,1,Meetme,${EXTEN:1}
; park channel for client GUI parking, hangup after 30 minutes
; create a GSM formatted audio file named "park.gsm" that is 30 minutes long
; and put it in /var/lib/asterisk/sounds
exten => 8301,1,Answer
exten => 8301,2,AGI(park_CID.agi)
exten => 8301,3,Playback(park)
exten => 8301,4,Hangup
exten => 8303,1,Answer
exten => 8303,2,AGI(park_CID.agi)
exten => 8303,3,Playback(conf)
exten => 8303,4,Hangup
; park channel for client GUI conferencing, hangup after 30 minutes
; create a GSM formatted audio file named "conf.gsm" that is 30 minutes long
; and put it in /var/lib/asterisk/sounds
exten => 8302,1,Answer
exten => 8302,2,Playback(conf)
exten => 8302,3,Hangup
exten => 8304,1,Answer
exten => 8304,2,Playback(ding)
exten => 8304,3,Hangup
; default audio for safe harbor 2-second-after-hello message then hangup
; create a GSM formatted audio file complies with safe harbor rules
; and put it in /var/lib/asterisk/sounds then change filename below
exten => 8307,1,Answer
exten => 8307,2,Playback(vm-goodbye)
exten => 8307,3,Hangup
; this is used for playing a message to an answering machine forwarded from AMD in VICIDIAL
exten => 8320,1,AGI(VD_amd.agi,${EXTEN}-----YES)
exten => 8320,2,Hangup
exten => _8320*.,1,AGI(VD_amd.agi,${EXTEN}-----YES)
exten => _8320*.,2,Hangup
; use for selective CallerID hangup by area code(hard-coded)
exten => 8352,1,AGI(agi-VDADselective_CID_hangup.agi,${EXTEN})
exten => 8352,2,Playback(safe_harbor)
exten => 8352,3,Hangup
; this is used for sending DTMF signals within conference calls, the client app
; sends the digits to be played in the callerID field
; sound files must be placed in /var/lib/asterisk/sounds
exten => 8500998,1,Answer
exten => 8500998,2,Playback(silence)
exten => 8500998,3,AGI(agi-dtmf.agi)
exten => 8500998,4,Hangup
; multi-remote-monitor entry extensions
exten => 8162,1,Dial(${TRUNKblind}/34567890123456789,55,to)
exten => 34567890123456789,1,Answer
exten => 34567890123456789,2,Goto(monitor,s,1)
;#### VDAD STANDARD TRANSFER ENTRIES ####
; Below are the parameters needed for the agi-VDAD_ALL_outbound.agi script to be run properly
; 1. the method of call handling for the script:
; - NORMAL - <default> Standard outbound routing to agent
; - TEST - For performance testing only
; - BROADCAST - For no-agent broadcast dialing
; - SURVEY - For survery question then on to agent
; - REMINDER - Reminder campaign
; - REMINDX - Reminder with transfer to agent
; 2. the method of searching for an available agent:
; - LB - <default> Load Balance total system
; - LO - Load Balance Overflow only (priority to home server)
; - SO - Home server only
; 3. the sound file to play when doing a SURVEY, REMINDER, REMINDX campaign
; 4. the acceptible dtmf digits for a SURVEY
; 5. the out-opt digit for a SURVEY (must be in the digit map)
; 6. the sound file to play for a SURVEY when transfering to an agent
; 7. the sound file to play for a SURVEY when DNCing the call
; 8. OPTIN or OPTOUT: if OPTIN call is only sent to agent with button press
; if OPTOUT call is sent to agent if no button press at all
; 9. the status that is use for a SURVEY when someone opts out
; if the status is DNC it will also add them to the internal dnc table
; VICIDIAL_auto_dialer transfer script for no-agent campaigns:
exten => 8364,1,Playback(sip-silence)
exten => 8364,2,AGI(agi://127.0.0.1:4577/call_log)
exten => 8364,3,AGI(agi-VDAD_ALL_outbound.agi,NORMAL-----LB)
exten => 8364,4,AGI(agi-VDAD_ALL_outbound.agi,NORMAL-----LB)
exten => 8364,5,Hangup
; VICIDIAL_auto_dialer transfer script:
exten => 8365,1,Playback(sip-silence)
exten => 8365,2,AGI(agi://127.0.0.1:4577/call_log)
exten => 8365,3,AGI(agi-VDAD_ALL_outbound.agi,NORMAL-----SO)
exten => 8365,4,AGI(agi-VDAD_ALL_outbound.agi,NORMAL-----SO)
exten => 8365,5,Hangup
; VICIDIAL_auto_dialer transfer script SURVEY at beginning:
exten => 8366,1,Playback(sip-silence)
exten => 8366,2,AGI(agi://127.0.0.1:4577/call_log)
exten => 8366,3,AGI(agi-VDAD_ALL_outbound.agi,SURVEYCAMP-----LB)
exten => 8366,4,AGI(agi-VDAD_ALL_outbound.agi,SURVEYCAMP-----LB)
exten => 8366,5,Hangup
; VICIDIAL_auto_dialer transfer script Load Balance Overflow:
exten => 8367,1,Playback(sip-silence)
exten => 8367,2,AGI(agi://127.0.0.1:4577/call_log)
exten => 8367,3,AGI(agi-VDAD_ALL_outbound.agi,NORMAL-----LO)
exten => 8367,4,AGI(agi-VDAD_ALL_outbound.agi,NORMAL-----LO)
exten => 8367,5,Hangup
; VICIDIAL_auto_dialer transfer script Load Balanced:
exten => 8368,1,Playback(sip-silence)
exten => 8368,2,AGI(agi://127.0.0.1:4577/call_log)
exten => 8368,3,AGI(agi-VDAD_ALL_outbound.agi,NORMAL-----LB)
exten => 8368,4,AGI(agi-VDAD_ALL_outbound.agi,NORMAL-----LB)
exten => 8368,5,Hangup
; VICIDIAL_auto_dialer transfer script AMD with Load Balanced:
exten => 8369,1,Playback(sip-silence)
exten => 8369,2,AGI(agi://127.0.0.1:4577/call_log)
exten => 8369,3,AMD(2000|2000|1000|5000|120|50|4|256)
exten => 8369,4,AGI(VD_amd.agi,${EXTEN})
exten => 8369,5,AGI(agi-VDAD_ALL_outbound.agi,NORMAL-----LB)
exten => 8369,6,AGI(agi-VDAD_ALL_outbound.agi,NORMAL-----LB)
exten => 8369,7,Hangup
; VICIDIAL auto-dial reminder script
exten => 8372,1,Playback(sip-silence)
exten => 8372,2,AGI(agi://127.0.0.1:4577/call_log)
exten => 8372,3,AGI(agi-VDADautoREMINDER.agi,${EXTEN})
exten => 8372,4,AGI(agi-VDADautoREMINDER.agi,${EXTEN})
exten => 8372,5,Hangup
; VICIDIAL SURVEY transfer script AMD with Load Balanced:
exten => 8373,1,Playback(sip-silence)
exten => 8373,2,AGI(agi://127.0.0.1:4577/call_log)
exten => 8373,3,AMD(2000|2000|1000|5000|120|50|4|256)
exten => 8373,4,AGI(VD_amd.agi,${EXTEN})
exten => 8373,5,AGI(agi-VDAD_ALL_outbound.agi,SURVEYCAMP-----LB)
exten => 8373,6,AGI(agi-VDAD_ALL_outbound.agi,SURVEYCAMP-----LB)
exten => 8373,7,Hangup
; VICIDIAL SURVEY transfer script with Cepstral names:
exten => 8374,1,Playback(sip-silence)
exten => 8374,2,AGI(agi://127.0.0.1:4577/call_log)
exten => 8374,3,AGI(agi-VDAD_ALL_outbound.agi,SURVEYCAMPCEP-----LB)
exten => 8374,4,AGI(agi-VDAD_ALL_outbound.agi,SURVEYCAMPCEP-----LB)
exten => 8374,5,Hangup
; VICIDIAL SURVEY transfer script AMD with Cepstral variables:
exten => 8375,1,Playback(sip-silence)
exten => 8375,2,AGI(agi://127.0.0.1:4577/call_log)
exten => 8375,3,AMD(2000|2000|1000|5000|120|50|4|256)
exten => 8375,4,AGI(VD_amd.agi,${EXTEN})
exten => 8375,5,AGI(agi-VDAD_ALL_outbound.agi,SURVEYCAMPCEP-----LB)
exten => 8375,6,AGI(agi-VDAD_ALL_outbound.agi,SURVEYCAMPCEP-----LB)
exten => 8375,7,Hangup
; PERFORMANCE TESTING
exten => _999XXXXXX1,1,Answer
exten => _999XXXXXX1,2,Wait(2)
exten => _999XXXXXX1,3,Playback(vicidial-welcome)
exten => _999XXXXXX1,4,Hangup
exten => _999XX11112,1,Wait(2)
exten => _999XX11112,2,Answer
exten => _999XX11112,3,Playback(ss-noservice)
exten => _999XX11112,4,Playback(vm-goodbye)
exten => _999XX11112,5,Hangup
exten => _999XX18112,1,Wait(2)
exten => _999XX18112,2,Answer
exten => _999XX18112,3,Playback(vtiger-fax)
exten => _999XX18112,4,Playback(vtiger-fax)
exten => _999XX18112,5,Hangup
exten => _999XX19112,1,Wait(2)
exten => _999XX19112,2,Answer
exten => _999XX19112,3,Playback(vtiger-email)
exten => _999XX19112,4,Playback(vtiger-email)
exten => _999XX19112,5,Hangup
exten => _999XXXX112,1,Wait(5)
exten => _999XXXX112,2,Answer
exten => _999XXXX112,3,Playback(demo-instruct)
exten => _999XXXX112,4,Playback(demo-instruct)
exten => _999XXXX112,5,Hangup
exten => _999XXXXXX2,1,Wait(8)
exten => _999XXXXXX2,2,Answer
exten => _999XXXXXX2,3,Playback(demo-instruct)
exten => _999XXXXXX2,4,Hangup
exten => _999XXXXXX3,1,Set(PRI_CAUSE=1)
exten => _999XXXXXX3,2,Hangup
exten => _999XXXXXX4,1,Set(PRI_CAUSE=27)
exten => _999XXXXXX4,2,Hangup
exten => _999XXXXXX5,1,Wait(60)
exten => _999XXXXXX5,2,Hangup
exten => _999XXXXXX6,1,Wait(10)
exten => _999XXXXXX6,2,Answer
exten => _999XXXXXX6,3,Playback(demo-instruct)
exten => _999XXXXXX6,4,Hangup
exten => _999XXXXXX7,1,Wait(12)
exten => _999XXXXXX7,2,Answer
exten => _999XXXXXX7,3,Playback(demo-enterkeywords)
exten => _999XXXXXX7,4,Hangup
exten => _999XXXXXX8,1,Set(PRI_CAUSE=17)
exten => _999XXXXXX8,2,Hangup
exten => _999XXXXXX9,1,Wait(6)
exten => _999XXXXXX9,2,Answer
exten => _999XXXXXX9,3,Playback(demo-abouttotry)
exten => _999XXXXXX9,4,Hangup
exten => _999XXXXXX0,1,Wait(5)
exten => _999XXXXXX0,2,Answer
exten => _999XXXXXX0,3,Playback(vm-goodbye)
exten => _999XXXXXX0,4,Hangup
exten => 99999999999,1,Answer
exten => 99999999999,2,Playback(conf)
exten => 99999999999,3,Playback(conf)
exten => 99999999999,4,Playback(conf)
exten => 99999999999,5,Playback(conf)
exten => 99999999999,6,Playback(conf)
exten => 99999999999,7,Playback(conf)
exten => 99999999999,8,Playback(conf)
exten => 99999999999,9,Playback(conf)
exten => 99999999999,10,Playback(conf)
exten => 99999999999,11,Playback(conf)
exten => 99999999999,12,Playback(conf)
exten => 99999999999,13,Playback(conf)
exten => 99999999999,14,Hangup
[monitor]
exten => h,1,DeadAGI(agi://127.0.0.1:4577/call_log--HVcauses ... EBUG-----${HANGUPCAUSE}-----${DIALSTATUS}-----${DIALEDTIME}-----${ANSWEREDTIME})
exten => s,1,Set(TIMEOUT(digit)=10)
exten => s,n,Set(TIMEOUT(response)=10)
exten => s,n,Set(MEETME_EXIT_CONTEXT=monitor_exit)
exten => s,n,Background(vm-extension) ; need audio prompt.
exten => s,n,WaitExten(10)
exten => i,1,Goto(monitor_exit,s,1)
exten => #,1,Goto(monitor_exit,s,1)
exten => t,1,Goto(monitor_exit,s,1)
exten => _8[0-2]XX,1,Meetme(8600${EXTEN:1},mqX) ; Listen
exten => _99[0-2]XX,1,Meetme(8600${EXTEN:2},X) ; Barge
[monitor_exit]
exten => h,1,DeadAGI(agi://127.0.0.1:4577/call_log--HVcauses ... EBUG-----${HANGUPCAUSE}-----${DIALSTATUS}-----${DIALEDTIME}-----${ANSWEREDTIME})
exten => _X,1,Goto(monitor,s,1)
exten => i,1,Goto(monitor,s,1)
exten => #,1,Goto(monitor,s,1)
exten => t,1,Goto(monitor,s,1)
- richie.gbpec
- Posts: 19
- Joined: Tue Jan 04, 2011 7:43 am
by williamconley » Fri Jan 21, 2011 9:26 am
I am *so* not gonna read your entire extensions.conf file. Just show how it differs from the standard instead please.
Vicidial Installation and Repair, plus Hosting and Colocation
Newest Product: Vicidial Agent Only Beep - Beta
http://www.PoundTeam.com # 352-269-0000 # +44(203) 769-2294
Newest Product: Vicidial Agent Only Beep - Beta
http://www.PoundTeam.com # 352-269-0000 # +44(203) 769-2294
- williamconley
- Posts: 20258
- Joined: Wed Oct 31, 2007 4:17 pm
- Location: Davenport, FL (By Disney!)
by richie.gbpec » Mon Jan 24, 2011 3:36 am
Thanks for your prompt reply. Let me simplify my post. In VICIDIAL, we used the following extensions.conf:
[general]
static=yes
writeprotect=no
[default]
exten=>_91XXXXXXXXXX,1,Dial(DAHDI/g1/0${EXTEN:2},30|o)
exten=>_91XXXXXXXXXX,n,Hangup()
; VICIDIAL_auto_dialer transfer script SURVEY at beginning:
;exten => 8366,1,AGI(agi://127.0.0.1:4577/call_log) ------->NOTE:We have commented out the log AGI
exten => 8366,n,Playback(welcome_tofrenzo_the_best_way_english)
exten => 8366,n,Hangup
;exten => h,1,DeadAGI(agi://127.0.0.1:4577/call_log--HVcauses ... EBUG-----${HANGUPCAUSE}-----${DIALSTATUS}-----${DIALEDTIME}-----${ANSWEREDTIME}) ------->NOTE:We have commented out the log AGI
<----WE HAVE REMOVED ALL OTHER EXTENSIONS ENTRY FROM THE STANDARD extensions.conf---->
The difference as evident above, is that we had removed most of the extensions provided by vicidial post installation,the prompt playback was defined in the extensions.conf and we commented out the AGI call to call_log. Everything seems fine when we ran the auto dial outbound survey campaign test.
However, when we ran auto dial outbound survey campaign with the standard extensions.conf, surprisngly, we get perceptible delay in prompt playback ranging from 5 to 12 seconds when user answers the call. I am copying the log from master.csv, where I noticed the delay of 5 seconds (see 5 written before "ANSWERED" in log below) in transfering the call from local channel to dahdi channel.
"","0000000000","919651363002","default","""V0120124232000000220"" <0000000000>","Local/919651363002@default-8196,2","DAHDI/29-1","Dial","DAHDI/g1/09651363002|30|o","2011-01-20 07:13:12","2011-01-20 07:13:41","2011-01-20 07:13:46",34,5,"ANSWERED","DOCUMENTATION","1295507592.633",""
This delay was not noticed when I ran VICIDIAL with our modified extensions.conf
What in your opnion could be going here. Curious to know how to remove this delay with standard extensions.conf file, since we believe standard file is the right way to do this campaign
[general]
static=yes
writeprotect=no
[default]
exten=>_91XXXXXXXXXX,1,Dial(DAHDI/g1/0${EXTEN:2},30|o)
exten=>_91XXXXXXXXXX,n,Hangup()
; VICIDIAL_auto_dialer transfer script SURVEY at beginning:
;exten => 8366,1,AGI(agi://127.0.0.1:4577/call_log) ------->NOTE:We have commented out the log AGI
exten => 8366,n,Playback(welcome_tofrenzo_the_best_way_english)
exten => 8366,n,Hangup
;exten => h,1,DeadAGI(agi://127.0.0.1:4577/call_log--HVcauses ... EBUG-----${HANGUPCAUSE}-----${DIALSTATUS}-----${DIALEDTIME}-----${ANSWEREDTIME}) ------->NOTE:We have commented out the log AGI
<----WE HAVE REMOVED ALL OTHER EXTENSIONS ENTRY FROM THE STANDARD extensions.conf---->
The difference as evident above, is that we had removed most of the extensions provided by vicidial post installation,the prompt playback was defined in the extensions.conf and we commented out the AGI call to call_log. Everything seems fine when we ran the auto dial outbound survey campaign test.
However, when we ran auto dial outbound survey campaign with the standard extensions.conf, surprisngly, we get perceptible delay in prompt playback ranging from 5 to 12 seconds when user answers the call. I am copying the log from master.csv, where I noticed the delay of 5 seconds (see 5 written before "ANSWERED" in log below) in transfering the call from local channel to dahdi channel.
"","0000000000","919651363002","default","""V0120124232000000220"" <0000000000>","Local/919651363002@default-8196,2","DAHDI/29-1","Dial","DAHDI/g1/09651363002|30|o","2011-01-20 07:13:12","2011-01-20 07:13:41","2011-01-20 07:13:46",34,5,"ANSWERED","DOCUMENTATION","1295507592.633",""
This delay was not noticed when I ran VICIDIAL with our modified extensions.conf
What in your opnion could be going here. Curious to know how to remove this delay with standard extensions.conf file, since we believe standard file is the right way to do this campaign
- richie.gbpec
- Posts: 19
- Joined: Tue Jan 04, 2011 7:43 am
by williamconley » Mon Jan 24, 2011 7:50 am
you still have not posted your installation .iso name/version
i'm also interested to know the environment it is being installed into. is it virtual?
so you are using 8366 (survey vdad exten) and you are experiencing a delay before the recording is being played ... the next question is whether you were playing the recording in the survey section of the campaign (set up in the GUI) or if you were modifying the extensions.conf already at that point.
you could certainly put back EVERYTHING except the 8366 extension and see if the problem appears/disappears with the standard/non-standard 8366.
also verify that you have some form of dummy timing source (which we could discuss in detail if you had listed your installer iso version and name, but ... i'm still not sure what your installation method was )
i'm also interested to know the environment it is being installed into. is it virtual?
so you are using 8366 (survey vdad exten) and you are experiencing a delay before the recording is being played ... the next question is whether you were playing the recording in the survey section of the campaign (set up in the GUI) or if you were modifying the extensions.conf already at that point.
you could certainly put back EVERYTHING except the 8366 extension and see if the problem appears/disappears with the standard/non-standard 8366.
also verify that you have some form of dummy timing source (which we could discuss in detail if you had listed your installer iso version and name, but ... i'm still not sure what your installation method was
)Vicidial Installation and Repair, plus Hosting and Colocation
Newest Product: Vicidial Agent Only Beep - Beta
http://www.PoundTeam.com # 352-269-0000 # +44(203) 769-2294
Newest Product: Vicidial Agent Only Beep - Beta
http://www.PoundTeam.com # 352-269-0000 # +44(203) 769-2294
- williamconley
- Posts: 20258
- Joined: Wed Oct 31, 2007 4:17 pm
- Location: Davenport, FL (By Disney!)
by richie.gbpec » Mon Jan 24, 2011 11:59 am
Hi William,
Following is the setup detail:
VICIdial VERSION: 2.2.1-237
BUILD: 100510-2015
Asterisk 1.4.38-vici
Dahdi -2.2.4 complete version
kernel 2.6.18-128.el5PAE
RHEL v 5.3 (32 bit)
Sangoma cards = 2 (A104d QUAD T1/E1 AFT card each), No extra software
PRI's = 8
We have not used any .iso(Or Vicibox) for the installation of Vici. We followed the steps as mentioned in the SCRATCH_INSTALL.txt of the VICI tar file after installing asterisk.
The environment is a physical server and not virtual.
We tried both of the combinations that is,using/without using the 8366 survey vdad extension with the standard extensions.conf but the issue with the delay in playing prompts persisted.
However, with the non standard extensions.conf that is with the call to the call_log AGI commented out and the same extension i.e. VDAD 8366 used, there was no delay.
Kindly suggest if there is any standard practice that you are aware of, to eliminate the delay in calls without commenting out and modifying the standard extensions.conf.
Thanks.
Following is the setup detail:
VICIdial VERSION: 2.2.1-237
BUILD: 100510-2015
Asterisk 1.4.38-vici
Dahdi -2.2.4 complete version
kernel 2.6.18-128.el5PAE
RHEL v 5.3 (32 bit)
Sangoma cards = 2 (A104d QUAD T1/E1 AFT card each), No extra software
PRI's = 8
We have not used any .iso(Or Vicibox) for the installation of Vici. We followed the steps as mentioned in the SCRATCH_INSTALL.txt of the VICI tar file after installing asterisk.
The environment is a physical server and not virtual.
We tried both of the combinations that is,using/without using the 8366 survey vdad extension with the standard extensions.conf but the issue with the delay in playing prompts persisted.
However, with the non standard extensions.conf that is with the call to the call_log AGI commented out and the same extension i.e. VDAD 8366 used, there was no delay.
Kindly suggest if there is any standard practice that you are aware of, to eliminate the delay in calls without commenting out and modifying the standard extensions.conf.
Thanks.
- richie.gbpec
- Posts: 19
- Joined: Tue Jan 04, 2011 7:43 am
by williamconley » Mon Jan 24, 2011 12:46 pm
yes in fact there is. the easiest way to avoid the delay is to install vicidial properly. the easiest way to install vicidial properly is from vicibox redux 3.1.16.
if you do not install vicidial from a vicibox redux or vicibox or goautodial .iso ... you still have to install the original OS from an .iso image of some sort. it would be helpful to list the .iso image from which you installed your os (ie: OpenSuse 11.3 ... or is that your RHEL 5.3? Redhat is strictly not supported as an OS, you may want to discuss that with Gardo, who at least supports CentOS like I do, but Gardo has actually built a distro of vicidial that works in CentOS. You may want to "borrow" his installation scripts from GoAutoDial if you're in redhad). Listing your kernel is helpful, but the name and version of the OS can often help others with your same installation find you and help you. without that, all you get is "standard vicidial help", which of course will not help you directly as you did not install vicidial in a standard way. right?
that being said (you'll get directed help from someone with the same system If they ever have the opportunity to know that you have their system ... unless you ARE in Redhad, because I don't know if ANYONE is actually using redhat rather than CentOS ... but I can offer some generic tips):
output from "screen -list" would be nice
also output from dahdi_test
if you do not install vicidial from a vicibox redux or vicibox or goautodial .iso ... you still have to install the original OS from an .iso image of some sort. it would be helpful to list the .iso image from which you installed your os (ie: OpenSuse 11.3 ... or is that your RHEL 5.3? Redhat is strictly not supported as an OS, you may want to discuss that with Gardo, who at least supports CentOS like I do, but Gardo has actually built a distro of vicidial that works in CentOS. You may want to "borrow" his installation scripts from GoAutoDial if you're in redhad). Listing your kernel is helpful, but the name and version of the OS can often help others with your same installation find you and help you. without that, all you get is "standard vicidial help", which of course will not help you directly as you did not install vicidial in a standard way. right?
that being said (you'll get directed help from someone with the same system If they ever have the opportunity to know that you have their system ... unless you ARE in Redhad, because I don't know if ANYONE is actually using redhat rather than CentOS ... but I can offer some generic tips):
output from "screen -list" would be nice
also output from dahdi_test
Vicidial Installation and Repair, plus Hosting and Colocation
Newest Product: Vicidial Agent Only Beep - Beta
http://www.PoundTeam.com # 352-269-0000 # +44(203) 769-2294
Newest Product: Vicidial Agent Only Beep - Beta
http://www.PoundTeam.com # 352-269-0000 # +44(203) 769-2294
- williamconley
- Posts: 20258
- Joined: Wed Oct 31, 2007 4:17 pm
- Location: Davenport, FL (By Disney!)
by richie.gbpec » Tue Feb 01, 2011 3:03 am
Hi William,
The above issues were addressed with GoAutoDial on CentOS.
Thanks for the support
The above issues were addressed with GoAutoDial on CentOS.
Thanks for the support
- richie.gbpec
- Posts: 19
- Joined: Tue Jan 04, 2011 7:43 am
by williamconley » Tue Feb 01, 2011 9:00 am
That's what gardo is here for! to be sure you freaks that love CentOS are catered to
Hey! Didja know that CentOS has another telephone system available? (BlueBox will install FreeSwitch on CentOS in about 10 minutes, fully automated install ... NOW If I could just get Vicidial to work on it!!! I'll just ask Kumba, he can do anything ...)
Hey! Didja know that CentOS has another telephone system available? (BlueBox will install FreeSwitch on CentOS in about 10 minutes, fully automated install ... NOW If I could just get Vicidial to work on it!!! I'll just ask Kumba, he can do anything ...)
Vicidial Installation and Repair, plus Hosting and Colocation
Newest Product: Vicidial Agent Only Beep - Beta
http://www.PoundTeam.com # 352-269-0000 # +44(203) 769-2294
Newest Product: Vicidial Agent Only Beep - Beta
http://www.PoundTeam.com # 352-269-0000 # +44(203) 769-2294
- williamconley
- Posts: 20258
- Joined: Wed Oct 31, 2007 4:17 pm
- Location: Davenport, FL (By Disney!)
Re: Prompt playback delay Outbound Auto Dial
by mattyou1985 » Tue Apr 19, 2016 3:37 pm
WaitForSilence Options - If Wait For Silence is desired on calls that are detected as Answering Machines then this field has those options. There are two settings separated by a comma, the first option is how long to detect silence in milliseconds and the second option is for how many times to detect that before playing the message. Default is EMPTY for disabled. A standard value for this would be wait for 2 seconds of silence twice: 2000,2
found under campaign detail settings set it to 200,5 thats my setting and its working
found under campaign detail settings set it to 200,5 thats my setting and its working
- mattyou1985
- Posts: 111
- Joined: Tue Apr 19, 2016 3:30 pm
Re: Prompt playback delay Outbound Auto Dial
by millahjovich » Tue May 17, 2016 7:20 am
The above issues were addressed with GoAutoDial on CentOS
- millahjovich
- Posts: 5
- Joined: Tue May 17, 2016 7:17 am
Re: Prompt playback delay Outbound Auto Dial
by mattyou1985 » Sat May 28, 2016 11:04 am
millahjovich wrote:The above issues were addressed with GoAutoDial on CentOS
it very well might of been but i did a new install of goautodial 3.3 and i had that problem, dont no why but the fix worked
since then i ran a update and tryed agen with the setting EMPTY and it worked as if it was set to 200,2 if not better
so ime gessing that it was fixed befor release of 3.3 then it stoped working after release of 3.3 then new update and all back to normal
ime not a fill flower of bug fixes but i do like to do new installs for testing, moding, what ever i can think of to see if its worth moving to a new server ect
and sorry for late reply onley just seen the post you did still new to this foram
best regards
- mattyou1985
- Posts: 111
- Joined: Tue Apr 19, 2016 3:30 pm
13 posts
• Page 1 of 1
Who is online
Users browsing this forum: No registered users and 70 guests