i am not able to access to recordings

General and Support topics relating to ViciDialNow and GoAutoDial ISO installers

Moderators: enjay, williamconley, Op3r, Staydog, gardo, mflorell, MJCoate, mcargile, Kumba, s0lid

i am not able to access to recordings

Postby pavankumarmaddila » Thu Jan 13, 2011 10:03 am

i am not able to access to recordings it says you dont have have permission to this page kindly help me to sort out the problem, and also give me the commands to access to the recordings
pavankumarmaddila
 
Posts: 2
Joined: Thu Jan 13, 2011 9:55 am

Postby williamconley » Thu Jan 13, 2011 11:15 am

when you post, please post your entire configuration including (but not limited to) your installation method and vicidial version with build.

this IS a requirement for posting along with reading the stickies (at the top of each forum) and the manager's manual (available on EFLO.net, both free and paid versions)

You should also post: Asterisk version, telephony hardware (model number is helpful here), cluster information if you have one, and whether any other software is installed in the box. If your installation method is "from scratch" you must post your operating system and should also post the .iso version from which you installed your original operating system.

Similar to This:
Vicibox X.X from .iso | Vicidial X.X.X Build XXXX | Asterisk X.X.X | Single Server | No Digium/Sangoma Hardware | No Extra Software After Installation
_____

depends on your installation, but you may need to change your apache configuration files to allow your ip address permission (previous post here for that configuration step, from gardo :) ). I think this is in his getting started guide, but I haven't checked.
Vicidial Installation and Repair, plus Hosting and Colocation
Newest Product: Vicidial Agent Only Beep - Beta
http://www.PoundTeam.com # 352-269-0000 # +44(203) 769-2294
williamconley
 
Posts: 20258
Joined: Wed Oct 31, 2007 4:17 pm
Location: Davenport, FL (By Disney!)

pls check the info and do giude me

Postby pavankumarmaddila » Tue Jan 25, 2011 1:39 pm

hello sir , thanks for the response
i don t have a proper knowledge on this vicidial and asterisks , any how i hv checked with the dialer the vicidial version is 2.0.5-173 i ask you once again pls do guide me with the commands to get the vicidial recordings from the command prompt
thankyou
pavankumarmaddila
 
Posts: 2
Joined: Thu Jan 13, 2011 9:55 am

Postby williamconley » Tue Jan 25, 2011 2:02 pm

Absotively. I'll slow down a little.

First: How did you install your Vicidial System? (please post the name of your installation disk which should also include your version and likely the Operating System distro name)
Vicidial Installation and Repair, plus Hosting and Colocation
Newest Product: Vicidial Agent Only Beep - Beta
http://www.PoundTeam.com # 352-269-0000 # +44(203) 769-2294
williamconley
 
Posts: 20258
Joined: Wed Oct 31, 2007 4:17 pm
Location: Davenport, FL (By Disney!)

Postby DhwaniTechnologies » Sat Feb 05, 2011 1:21 am

Dear Pavan,

I know exactly what you're talking about. I have seen several this in the past. Its not a Vicidial issue, its just an Apache issue. There's a file called vicidial-recordings.conf in the /etc/httpd/conf directory. You need to allow your IP range to access the recordings directory. If you are a Linux person, you should be able to solve this. This Apache article will help:
http://www.cyberciti.biz/faq/apache-403 ... -solution/
Vicidial, Goautodial, OSdial Consulting | Hosted Solutions
Dhwani Technologies | info@dhwanitech.com | Skype: dhwanitech
DhwaniTechnologies
 
Posts: 46
Joined: Thu Oct 14, 2010 10:03 am
Location: US/India


Return to ViciDialNow - GoAutoDial

Who is online

Users browsing this forum: No registered users and 31 guests